Connect with us

News

SpaceX rolls last Starship off the assembly line ahead of “major upgrades”

SpaceX's fourth full-size Starship prototype is effectively complete. (NASASpaceflight - bocachicagal)

Published

on

SpaceX has installed Starship serial number 11’s (SN11) steel nosecone, effectively completing the rocket and marking the end of production for a series of four virtually identical prototypes.

SpaceX has soared through a limited production run of four full-height Starship prototypes with a more or less frozen design, simultaneously serving as a pilot run for a nascent Starship assembly line while also producing high-fidelity prototypes for the program’s first high-altitude flight testing. Work on Starship SN8 – the first of those four prototypes – began around July 2020 when labeled hardware was first spotted.

Parts of SN9, SN10, SN11, and SN12 gradually started to appear over the next few months. Less than four months after production began, (half of) Starship SN8 rolled to the launch pad in late October to kick off a series of acceptance tests.

After an unusually long ~6 weeks of testing, SpaceX declared Starship SN8 ready for flight and ultimately pulled off a high-altitude launch that made it just a dozen or so seconds (~5%) away from a complete success – far further than anyone really expected. That surprising level of success appeared to lead SpaceX to reevaluate its plans and the strategic design of its test plans.

One result was observed in publicly-visible labels SpaceX uses to identify the dozens of Starship parts in work at any given moment: after SN12, only a few minor unfinished parts of SN13 and SN14 were ever spotted, departing from the flood of activity observed while building SN8 through SN11. In November, CEO Elon Musk revealed that “major upgrades” were planned for Starship SN15 and all subsequent prototypes.

Advertisement

The implication was that SpaceX had already written off no fewer than three Starships (SN8-SN10) to prove that a new, exotic approach to rocket landings could work as planned. If those three failed, SpaceX could likely use Starships SN11 through SN14 – likely enough prototypes to either succeed or conclude that a redesign is necessary. Ultimately, after Starship SN8’s spectacular success and last-second failure, SpaceX seemingly concluded that it was unlikely to need a full seven prototypes to achieve the first soft landing(s) and effectively killed Starships SN12, SN13, and SN14 in the cradle.

On January 23rd, Starship SN12’s completed engine section was rather decisively scrapped before stacking had even begun. (NASASpaceflight – bocachicagal)

SpaceX likely concluded that SN8 had demonstrated that a vast majority of Starship’s existing design was already sound, reducing enough risk to confidently begin major upgrades – akin to building a more permanent structure only after ensuring that the foundation is stable. Indicating exactly that, SpaceX has already begun stacking Starship SN15 and has been churning out hardware for SN16, SN17, and SN18 for the last few months.

That ultimately means that one or more upgraded Starships will likely be ready to carry the torch forward as soon as SN10 and SN11 flight testing comes to an end – whether that means continuing recovery attempts or pushing the envelope higher and faster after the first successful soft landing(s).

The nature of those “upgrades” remains unclear beyond apparent fit-and-finish improvements and the possibility of a more easily manufacturable nosecone design, but it’s clear that things will become clearer far sooner than later at SpaceX’s current rate of progress.

SpaceX rolls Starship SN11 to the high bay for nose installation, February 5th.(NASASpaceflight – bocachicagal)
A worker prepares the top of SN11’s tank section for nose installation. (NASASpaceflight – bocachicagal)
Starship SN11’s assembly is effectively complete, likely meaning that the prototype will be ready to take over immediately if/when SN10 lands in less than one piece. (NASASpaceflight – bocachicagal)

Eric Ralph is Teslarati's senior spaceflight reporter and has been covering the industry in some capacity for almost half a decade, largely spurred in 2016 by a trip to Mexico to watch Elon Musk reveal SpaceX's plans for Mars in person. Aside from spreading interest and excitement about spaceflight far and wide, his primary goal is to cover humanity's ongoing efforts to expand beyond Earth to the Moon, Mars, and elsewhere.

Advertisement
Comments

Elon Musk

Elon Musk is now a remote DOGE worker: White House Chief of Staff

The Tesla and SpaceX CEO Elon Musk is no longer working from the West Wing.

Published

on

Credit: Elon Musk/X

In a conversation with the New York Post, White House Chief of Staff Susie Wiles stated that Tesla and SpaceX CEO Elon Musk is no longer working from the West Wing.

As per the Chief of Staff, Musk is still working for DOGE—as a remote worker, at least.

Remote Musk

In her conversation with the publication, Wiles stated that she still talks with Musk. And while the CEO is now working remotely, his contributions still have the same net effect. 

“Instead of meeting with him in person, I’m talking to him on the phone, but it’s the same net effect,” Wiles stated, adding that “it really doesn’t matter much” that the CEO “hasn’t been here physically.” She also noted that Musk’s team will not be leaving.

“He’s not out of it altogether. He’s just not physically present as much as he was. The people that are doing this work are here doing good things and paying attention to the details. He’ll be stepping back a little, but he’s certainly not abandoning it. And his people are definitely not,” Wiles stated.

Advertisement

Back to Tesla

Musk has been a frequent presence in the White House during the Trump administration’s first 100 days in office. But during the Q1 2025 Tesla earnings call, Musk stated that he would be spending substantially less time with DOGE and substantially more time with Tesla. Musk did emphasize, however, that DOGE’s work is extremely valuable and critical.

“I think I’ll continue to spend a day or two per week on government matters for as long as the President would like me to do so and as long as it is useful. But starting next month, I’ll be allocating probably more of my time to Tesla and now that the major work of establishing the Department of Government Efficiency is done,” Musk stated.

Continue Reading

Elon Musk

Tariff reprieve might be ‘Tesla-friendly,’ but it’s also an encouragement to others

Tesla stands to benefit from the tariff reprieve, but it has some work cut out for it as well.

Published

on

tesla employee
(Photo: Tesla)

After Secretary of Commerce Howard Lutnick made adjustments to the automotive tariff program that was initially announced, many quickly pointed to the reprieve as “Tesla-friendly.”

While that may be the case right now, it was also a nudge of encouragement to other companies, Tesla included, to source parts from the U.S. in an effort to strengthen domestic manufacturing. Many companies are close, and it will only take a handful of improvements to save themselves from tariffs on their cars as well.

Yesterday, Sec. Lutnick confirmed that cars manufactured with at least 85 percent of domestic content will face zero tariffs. Additionally, U.S. automakers would receive credit up to 15 percent of the value of vehicles to offset the cost of imported parts.

Big Tesla win? Sec Lutnick says cars with 85% domestic content will face zero tariffs

“This is ‘finish your cars in America and you win’,” Lutnick said.

Many were quick to point out that only three vehicles currently qualify for this zero-tariff threshold: all three are Teslas.

However, according to Kelley Blue Book’s most recent study that revealed who makes the most American cars, there are a lot of vehicles that are extremely close to also qualifying for these tariff reductions.

Tesla has three vehicles that are within five percent, while Ford, Honda, Jeep, Chevrolet, GMC, and Volkswagen have many within just ten percent of the threshold.

Tesla completely dominates Kogod School’s 2024 Made in America Auto Index

It is within reach for many.

Right now, it is easy to see why some people might think this is a benefit for Tesla and Tesla only.

But it’s not, because Tesla has its Cybertruck, Model S, and Model X just a few percentage points outside of that 85 percent cutoff. They, too, will feel the effects of the broader strategy that the Trump administration is using to prioritize domestic manufacturing and employment. More building in America means more jobs for Americans.

Credit: Tesla

However, other companies that are very close to the 85 percent cutoff are only a few components away from also saving themselves the hassle of the tariffs.

Ford has the following vehicles within just five percent of the 85 percent threshold:

  • Ford Mustang GT automatic (80%)
  • Ford Mustang GT 5.0 (80%)
  • Ford Mustang GT Coupe Premium (80%)

Honda has several within ten percent:

  • Honda Passport All-Wheel-Drive (76.5%)
  • Honda Passport Trailsport (76.5)

Jeep has two cars:

  • Jeep Wrangler Rubicon (76%)
  • Jeep Wrangler Sahara (76%)

Volkswagen has one with the ID.4 AWD 82-kWh (75.5%). GMC has two at 75.5% with the Canyon AT4 Crew Cab 4WD and the Canyon Denali Crew Cab 4WD.

Chevrolet has several:

  • Chevrolet Colorado 2.7-liter (75.5%)
  • Chevrolet Colorado LT Crew Cab 2WD 2.7-liter (75.5%)
  • Chevrolet Colorado Z71 Crew Cab 4WD 2.7-liter (75.5%)

These companies are close to reaching the 85% threshold, but adjustments need to be made to work toward that number.

Anything from seats to fabric to glass can be swapped out for American-made products, making these cars more domestically sourced and thus qualifying them for the zero-tariff boundary.

Frank DuBois of American University said that manufacturers like to see stability in their relationships with suppliers and major trade partners. He said that Trump’s tariff plan could cause “a period of real instability,” but it will only be temporary.

Now is the time to push American manufacturing forward, solidifying a future with more U.S.-made vehicles and creating more domestic jobs. Tesla will also need to scramble to make adjustments to its vehicles that are below 85%.

Continue Reading

News

Tesla Cybertruck RWD production in full swing at Giga Texas

Videos of several freshly produced Cybertruck LR RWD units were shared on social media platform X.

Published

on

Credit: Joe Tegtmeyer/X

It appears that Tesla is indeed ramping the production of the Cybertruck Long Range Rear Wheel Drive (LR RWD), the most affordable variant of the brutalist all-electric pickup truck.

Videos of several freshly produced Cybertruck LR RWD units were shared on social media platform X.

Giga Texas Footage

As per longtime Tesla watcher Joe Tegtmeyer, Giga, Texas, was a hotbed of activity when he conducted his recent drone flyover. Apart from what seemed to be Cybercab castings being gathered in the complex, a good number of Cybertruck LR RWD units could also be seen in the facility’s staging area. The Cybertruck LR RWD units are quite easy to spot since they are not equipped with the motorized tonneau cover that is standard on the Cybertruck AWD and Cyberbeast.

The presence of the Cybertruck LR RWD units in Giga Texas’ staging area suggests that Tesla is ramping the production of the base all-electric pickup truck. This bodes well for the vehicle, which is still premium priced despite missing a good number of features that are standard in the Cybertruck AWD and Cyberbeast.

Cybertruck Long Range RWD Specs

The Cybertruck LR RWD is priced at $69,990 before incentives, making it $10,000 more affordable than the Cybertruck AWD. For its price, the Cybertruck Long Range RWD offers a range of 350 miles per charge if equipped with its 18” standard Wheels. It can also add up to 147 miles of range in 15 minutes using a Tesla Supercharger.

Advertisement

Much of the cost-cutting measures taken by Tesla are evident in the cabin of the Cybertruck LR RWD. This could be seen in its textile seats, standard console, seven-speaker audio system with no active noise cancellation, and lack of a 9.4” second-row display. It is also missing the motorized tonneau cover, the 2x 120V and 1x 240V power outlets on the bed, and the 2x 120V power outlets in the cabin. It is also equipped with an adaptive coil spring suspension instead of the adaptive air suspension in the Cybertruck AWD and Cyberbeast.

Continue Reading

Trending