

News
SpaceX launches US spy satellite, nails Falcon 9 landing again
After a 24 hour delay due to a sensor failure Sunday morning, SpaceX successfully launched its first US spy satellite for the National Reconnaissance Office — NROL 76 — at 7:15 am EDT from launch pad 39A at Kennedy Space Center. Following first stage separation about 2 minutes and 48 seconds after liftoff, the live webcast was interrupted due to the classified nature of the payload. But shortly thereafter, the company announced the payload shroud had detached as planned, the final step necessary to deliver the satellite successfully into orbit.
At that point, all eyes focused on the flight of the Falcon 9 first stage rocket back to Kennedy Space Center where it was scheduled to land at Landing Zone 1. Onboard cameras let viewers watch as the Falcon 9 first stage descended through the clouds on its way back to earth, It slowed from a speed of more than 1,000 meters per second before coming to a complete stop right in the center of the 300 foot in diameter landing pad.
Chief Elon Musk posted an Instagram video showing a close-up of the impressive rocket sequence before touching down on land.
https://www.instagram.com/p/BTjVdLVB1bO/
Today’s mission marks the fourth time that SpaceX has successfully recovered the first stage of a Falcon 9 rocket at Landing Zone 1 and tenth self-landing since its historic flight in December of 2015. Back in March, SpaceX made history once again by successfully launching and landing a refurbished rocket that was previously flown. In a rare appearance on the live webcast at the time, Chief Elon Musk addressed viewers with an inspirational remark, saying “It’s an amazing day for space [and] as a whole for the space industry.” He would add, “This is ultimately going to be a huge revolution in space flight”.
During a TED talk in 2013, Elon Musk said in speaking about SpaceX’s goals, “It’s the first re-flight of an old booster where that re-flight is relevant,” Musk says. “Reusability is only relevant if it is rapid and complete, like an aircraft or a car … You don’t send your aircraft into Boeing in between flights.” Musk’s goal is to lower the turn around time from flight to reuse to 24 hours or less.
The success of today’s launch could be a key factor in securing more contracts from the US government — a vital part of the he company’s growth plans.
News
Tesla Gigafactory Texas builds its half millionth vehicle
The milestone was shared via Twitter/X by the official @Gigafactories account.

Tesla’s Gigafactory Texas has officially rolled out its 500,000th vehicle, marking a significant achievement in the factory’s history and reinforcing its role as a central hub in Tesla’s vehicle manufacturing network.
The milestone was shared via Twitter/X by the official @Gigafactories account. “Congratulations to the Giga Texas team for building 500k vehicles,” the company’s X post read.
As could be seen in Tesla Manufacturing’s post, the Gigafactory Texas team celebrated the milestone by posting for a photograph with the facility’s half millionth unit, a white Tesla Model Y. The team held balloons that spelled “500K” on its commemorative photo.
Giga Texas, located near Austin, has ramped its operations since its launch, producing Tesla’s Cybertruck and Model Y. Crossing the half-million vehicle mark solidifies the facility’s importance to Tesla’s overall operations, especially considering the fact that the Model Y is the company’s best-selling vehicle.
While Giga Texas is just producing the Model Y and the Cybertruck for now, the facility is also poised to produce the Cybercab. The Cybercab is expected to be Tesla’s highest volume vehicle, with Elon Musk estimating that the company would be producing about 2 million units of the autonomous two-seater per year.
The Cybercab is unlike any vehicle that is currently produced today, and its production would be quite extraordinary. As per Elon Musk’s previous comments, the Cybercab’s manufacturing line would not look like an automotive production line at all. Instead, Musk noted that the Cybercab’s line in Gigafactory Texas would resemble a high-speed consumer electronics line instead.
“We do want to scale up production to new heights obviously with the Cybercab. Cybercab is not just revolutionary car design. It’s also a revolutionary manufacturing process. So I guess we probably don’t talk about that enough, but if you’ve seen the design of the Cybercab line, it doesn’t look like a normal car manufacturing line. It looks like a really high-speed consumer electronics line,” Musk previously stated.
News
Tesla reportedly places large order for robot parts, hinting that Optimus V3 design is all but finalized
Tesla has reportedly placed a large order of linear actuators for humanoid robots from a Chinese supplier.

Tesla might have all but finalized the design for its Optimus V3 humanoid robot, at least if rumors from China prove accurate. As per recent reports, Tesla has reportedly placed a large order of linear actuators for humanoid robots from a Chinese supplier, with deliveries expected sometime in the first quarter of 2026.
The volume of orders suggested by the reports from China suggests that the components will not just be used for Optimus prototypes.
The rumor
As noted in a report from Sina News, media outlets across China have recently reported that Tesla has placed a $685 million (5 billion RMB) order for linear actuators from Sanhua Intelligent Controls. The components will reportedly be used for the production of Optimus, which will likely be mass-produced in its V3 iteration. The reports claimed that the delivery of the actuators will likely start sometime in the first quarter of 2026.
Industry watchers have estimated that such a volume would be enough for about 180,000 Optimus robots. This suggests that while Tesla might not be able to start the initial production of its humanoid robots this year, the electric vehicle maker might be able to hit the ground running with its Optimus production next year. And as hinted at by Elon Musk’s comments on X, Tesla seems to be preparing to produce Optimus V3 en masse.
Company comments
The reports of Tesla’s alleged actuator orders have resulted in Sanhua Intelligent Controls’ stock rising. Interestingly enough, a Tesla China representative has stated that “no official information about this order that could be disseminated externally.” A representative from Sanhua, on the other hand, simply stated that the company’s robotics business is progressing smoothly, but they could not comment on market rumors.
While these reports are rumors for now, there are some optimistic hints that Tesla might have all but finalized the design for Optimus V3, and the company might be looking to start the robot’s production. For one, Sanhua is already a Tesla supplier, providing components for the company’s electric cars. A report from The Information also alleged that Tesla is no longer looking to produce 5,000 Optimus robots in 2025. This was reportedly due to challenges in the robot’s hands.
If Tesla is really starting to order large volumes of components for Optimus’ production, it would suggest that the company might have overcome the challenges it was facing with the humanoid robot earlier this year. It would then not be farfetched if Tesla were able to start the initial production of Optimus V3 next year.
News
Tesla eyes two new states for Robotaxi

Tesla has officially shown that it is eyeing two new states for Robotaxi operation in the U.S., as it hopes to add the new areas to its ever-growing list of places where the suite is either active or in the testing phase.
Tesla first launched its Robotaxi suite in Austin, Texas, in late June. It expanded the suite to the San Francisco Bay Area just a month later. Since then, it has not launched any public rides in any other states, but it has gained several approvals for early testing.
In preparation for operation in new states, Tesla routinely lists job postings on its Careers website, which helps align potential employees with opportunities ahead of regulatory approvals. This is a strategy that allows Tesla to start operations immediately upon licensing for testing.
Tesla started hiring Vehicle Operators for Autopilot in Arizona and Nevada months before the company gained any sort of approvals from state governments for Robotaxi. However, those approvals eventually came in the form of testing licenses, which allow the company to perform validation ahead of its public launch.
Tesla begins validating Robotaxi in a new area, hinting at expansion
Now, Tesla has posted job listings for Vehicle Operators for Autopilot in two new states: Colorado and Illinois. The Colorado job listing is located in Aurora, a suburb of Denver. Tesla is looking for Robotaxi operators in Chicago as well.
These postings hint toward Tesla’s continuing efforts to expand Robotaxi to new places. Earlier this year, CEO Elon Musk said the company would like to have Robotaxi available to at least half of the U.S. population.
It has expanded significantly since its initial launch in late June, but it is still a far way off from where Tesla would like it to be by year’s end.
So far, Tesla has job listings for Autopilot Vehicle Operators in Arizona, California, Texas, Florida, Colorado, Nevada, and Illinois.
-
News1 week ago
Tesla FSD (Supervised) V14.1 with Robotaxi-style dropoffs is here
-
Elon Musk3 hours ago
Starship’s next chapter: SpaceX eyes tower catch after flawless Flight 11
-
News1 week ago
Tesla all but confirms that affordable Model Y is coming Tuesday
-
Elon Musk2 weeks ago
Elon Musk announces ‘Grokipedia’ as Wikipedia alternative from xAI
-
News4 hours ago
Tesla reportedly places large order for robot parts, hinting that Optimus V3 design is all but finalized
-
Elon Musk1 week ago
Tesla releases cryptic teaser for something massive and it’s coming this week
-
Investor's Corner2 weeks ago
Tesla Q3 deliveries expected to exceed 440k as Benchmark holds $475 target
-
News1 week ago
Tesla plant manager tips off affordable model production