News
SpaceX installs second Starship-derived fuel tank at orbital launch pad
For the second time in two weeks, SpaceX has rolled a ‘Starship-derived’ propellant tank to the next-generation rocket’s first orbital launch pad, continuing a recent burst of construction activity.
Precisely two weeks ago, SpaceX rolled the first of those massive ground support equipment (GSE) propellant tanks the 1.5 miles from its Boca Chica rocket factory to a nearby launch complex. Built with the same parts, facilities, and equipment as flightworthy Starship prototypes, SpaceX’s plans to build grounded storage tanks out of rocket parts went from a complete surprise to initial hardware delivery in less than two months.
Two weeks later, SpaceX has already completed the second of at least seven similar or identical tanks that should be able to store enough propellant for two back-to-back orbital Starship launches – and a third ‘GSE’ tank is just a week or so behind it.
As previously discussed on Teslarati, SpaceX’s decision to use a literal rocket factory to build custom propellant storage tanks is surprisingly revealing with a few reasonable assumptions in place.
SpaceX is effectively taking interchangeable Starship parts, slightly tweaking a handful of them, and turning what could have been a rocket into a propellant storage tank. This is significant because relative to all other rockets in history, even including SpaceX’s own Falcon 9 and Heavy, building storage tanks with unchanged rocket parts on a rocket assembly line would be roughly akin to hiring Vincent van Gogh to paint lane lines.
The existence of self-built propellant storage tanks virtually identical to flightworthy Starship airframes all but guarantees that SpaceX is already building Starships for a few million dollars each – and possibly much less.“
Teslarati.com – 6 April 2021
Aside from potentially being dirt-cheap bulk storage tanks that all but guarantee SpaceX can produce Starship and its Super Heavy boosters for pennies on the dollar of any other rocket in history, SpaceX is quickly demonstrating that it can build a lot of them – and quickly. Parts of Starship prototypes SN17 through SN20 and Super Heavy boosters BN2 and BN3 continue to slowly trickle out of SpaceX’s factory and Starship SN16 is steadily progressing towards completion to take over wherever SN15 leaves off.
However, at least a majority of SpaceX’s focus appears to be set on mass-producing propellant storage tanks as quickly as possible in order to prepare Starship’s orbital launch pad – deep into construction – for flight tests involving Super Heavy. Just last month, following a sourced report from NASASpaceflight.com, CEO Elon Musk confirmed that SpaceX intends to attempt Starship’s first launch on a Super Heavy booster as early as July 2021 – just three months from now.
For obvious reasons, the odds are firmly stacked against SpaceX attempting Starship’s first orbital launch mere months from now, though such an attempt would still be extremely impressive if it happens in 2021 at all. To even attempt that extraordinarily ambitious feat, SpaceX will have to complete at least a barebones ‘rough draft’ of its planned orbital launch complex, including at least four Starship-style GSE tanks.
Towards that end, GSE tank #3 (GSE-3) is already more than half complete and parts of GSE-4 are in work, likely meaning that SpaceX will have enough installed propellant storage capacity for orbital Starship launch attempts less than a month from now. It remains to be seen if SpaceX will power through tanks 5 through 7 after 3 and 4 are complete, or if the focus will shift back to Starship and Super Heavy prototype production.
Either way, SpaceX is wasting no time constructing a brand new super heavy-class launch pad and a tank farm the likes of which has never been seen before. For now, we’ll have to wait and see how long it takes Starship and Super Heavy to catch up.
News
Tesla Cybercab display highlights interior wizardry in the small two-seater
Photos and videos of the production Cybercab were shared in posts on social media platform X.
The Tesla Cybercab is currently on display at the U.S. Department of Transportation in Washington, D.C., and observations of the production vehicle are highlighting some of its notable design details.
Photos and videos of the production Cybercab were shared in posts on social media platform X.
Observers of the Cybercab display unit noted that the two-seat Robotaxi provides unusually generous legroom for a vehicle of its size. Based on the vehicle’s video, the compact two-seater appears to offer more legroom than Tesla’s larger vehicles such as the Model Y, Model X, and Cybertruck.
The Cybercab’s layout allows Tesla to dedicate nearly the entire cabin to passengers. The vehicle is designed without a steering wheel or pedals, which helps maximize interior space.
Footage from the display also highlights the Cybercab’s large center screen, which is positioned prominently in front of the passenger bench. The display appears intended to provide entertainment and ride information while the vehicle operates autonomously.
Images of the vehicle also show an additional camera integrated into the Cybercab’s C-pillar. The extra camera appears to expand the vehicle’s field of view, which would be useful as Tesla works toward fully unsupervised Full Self-Driving.
Tesla engineers have previously explained that the Cybercab was designed to be highly efficient both in manufacturing and in operation. Cybercab Lead Engineer Eric E. stated in 2024 that the Robotaxi would be built with roughly half the number of parts used in a Model 3 sedan.
“Two seats unlocks a lot of opportunity aerodynamically. It also means we cut the part count of Cybercab down by a substantial margin. We’re gonna be delivering a car that has roughly half the parts of Model 3 today,” the Tesla engineer said.
The Tesla engineer also noted that the Cybercab’s cargo area can accommodate multiple golf bags, two carry-on suitcases, and two full-size checked bags. The trunk can also fit certain bicycles and a foldable wheelchair depending on size, which is quite impressive for a small car like the Cybercab.
Elon Musk
Elon Musk’s xAI wins permit for power plant supporting AI data centers
The development was reported by CNBC, citing confirmation from the Mississippi Department of Environmental Quality (MDEQ).
Mississippi regulators have approved a permit allowing Elon Musk’s artificial intelligence company xAI to construct a natural gas power plant in Southaven. The facility is expected to support the company’s expanding AI infrastructure tied to its Colossus data center operations near Memphis.
The development was reported by CNBC, citing confirmation from the Mississippi Department of Environmental Quality (MDEQ).
According to the report, regulators “voted to approve the permit” of xAI subsidiary MZX Tech LLC to construct a power plant featuring 41 natural gas-burning turbines “after careful consideration of all public comments and community concerns.”
The Mississippi Department of Environmental Quality stated that the permit followed a regulatory review process that included public comments and community input. Jaricus Whitlock, air division chief for the MDEQ, stated that the project met all applicable environmental standards.
“The proposed PSD permit in front of the board today not only meets all state and federal permitting regulations, but goes above and beyond what is required by law. MDEQ and the EPA agree that not a single person around our facilities will be exposed to unhealthy levels of air pollution,” Whitlock stated.
The planned facility will help provide electricity for xAI’s AI computing infrastructure in the Memphis region.
The Southaven project forms part of xAI’s efforts to scale computing capacity for its artificial intelligence systems.
The company currently operates two major data centers in Memphis, known as Colossus 1 and Colossus 2, which provide computing power for xAI’s Grok AI models. xAI is also planning to build another large data center in Southaven called Macrohardrr, which would be located in a warehouse previously used by GXO Logistics.
Large-scale AI training requires substantial computing power and electricity, prompting technology companies to develop dedicated energy infrastructure for their data centers.
SpaceX President Gwynne Shotwell previously stated that xAI plans to develop 1.2 gigawatts of power capacity for its Memphis-area AI supercomputer site as part of the federal government’s Ratepayer Protection Pledge. The commitment was announced during an event with United States President Donald Trump.
“As part of today’s commitment, we will take extensive additional steps to continue to reduce the costs of electricity for our neighbors. xAI will therefore commit to develop 1.2 GW of power as our supercomputer’s primary power source. That will be for every additional data center as well. We will expand what is already the largest global Megapack power installation in the world,” Shotwell said.
“The installation will provide enough backup power to power the city of Memphis, and more than sufficient energy to power the town of Southaven, Mississippi where the data center resides. We will build new substations and invest in electrical infrastructure to provide stability to the area’s grid.”
Elon Musk
Tesla China teases Optimus robot’s human-looking next-gen hands
The image was shared by Tesla AI’s account on Weibo and later reposted by Tesla community members on X.
A new teaser shared by Tesla’s China team appears to show a pair of unusually human-like hands for Optimus.
The image was shared by Tesla AI’s account on Weibo and later reposted by Tesla community members on X.
As could be seen in the teaser image, the new version of Optimus’ hands features proportions and finger structures that look strikingly similar to those of a human hand. Their appearance suggests that they might have dexterity approaching that of a human hand.
If the image reflects a new generation of Optimus’ hands, it could indicate Tesla is continuing to refine one of the most critical components of its humanoid robot.
Hands are widely viewed as one of the most difficult engineering challenges in robotics. For Optimus to perform complex real-world work, from manufacturing tasks to household activities, its hands would need to be the best in the industry.
Elon Musk has repeatedly described Optimus as Tesla’s most important long-term product. In posts on social media platform X, Musk has stated that Optimus could eventually become the first real-world Von Neumann machine.
In theory, a Von Neumann machine is a self-replicating system capable of building copies of itself using available materials. The concept was originally proposed by mathematician John von Neumann in the mid-20th century.
“Optimus will be the first Von Neumann machine, capable of building civilization by itself on any viable planet,” Musk wrote in a post on X.
If Optimus is expected to carry out complex work autonomously in the future, high levels of dexterity will likely be essential. This makes the development of advanced robotic hands a key step towards Musk’s long-term expectations for the product.
Tesla Cybercab display highlights interior wizardry in the small two-seater
Elon Musk’s xAI wins permit for power plant supporting AI data centers
