

News
NASA’s SLS Moon rocket is almost ready for its first trip to the launch pad
NASA says its first complete Space Launch System (SLS) rocket is less than a week away from its first rollout and the start of its first East Coast ‘wet dress rehearsal’.
Teams have begun retracting work platforms surrounding the fully stacked rocket, slowly revealing the launch vehicle assigned to Artemis 1 – a much anticipated and extensively delayed uncrewed test flight of the SLS rocket and Orion spacecraft. Since April 2021, SLS and Orion have been slowly but surely assembled within the Vehicle Assembly Building (VAB) at NASA’s Kennedy Space Center in Cape Canaveral, Florida.
Preparing the rocket for the launch pad has required an arduous and complex series of tests meant to ensure that the vehicle is ready for the stresses it will experience and the operations it will perform before and during launch. The rollout is expected to begin around 5 pm EST (22:00 UTC) on Thursday, March 17th and, if all goes well, it should take the giant crawler tasked with carrying the rocket and ‘mobile launch platform’ about 12 hours to carry them to Launch Complex 39B (LC-39B or Pad 39B). The first hour of the rollout will extricate the rocket and its mobile launch tower from the VAB, followed by an 11-hour journey to the pad.
NASA says SLS will spend around one month at Pad 39B, during which it will undergo expensive testing required to ensure its launch readiness. After two weeks on the pad, SLS will have its tanks filled with liquid hydrogen (LH2) and liquid oxygen (LOx) propellant and run through a simulated countdown in a process known as a wet dress rehearsal (WDR). Representatives of the Artemis-1 mission indicate “the countdown will end at about [T-minus 9 seconds], which is just moments before the rocket’s four RS-25 engines would ignite [before] an actual launch.” By allowing the countdown to run so low, test teams are able to check all interfaces (aside from the rocket’s RS-25 engines) that must be carefully coordinated during launch.
Once the wet-dress is complete, SLS will be rolled back into the VAB for final launch preparations, including the identification and repair of any issues found during wet-dress, final Orion spacecraft work, and flight software updates. After SLS’ return to the VAB, NASA expects that final work to take one month to complete. However, NASA officials admit that there is still a lot of work to be done to SLS before launch, and almost every aspect of the space agency’s work on the rocket over the last two and a half years has run into extensive delays.
An official launch date has not been chosen by NASA, as delays continue to make setting a specific date impractical. Tom Whitmeyer, NASA deputy associate administrator for exploration systems development, has indicated that a launch in April is no longer feasible. “We’re still evaluating the tail end of the May window,” he said, which runs from May 7 to 21. Future launch windows, governed by orbital mechanics and other mission constraints like ensuring that Orion is recovered in daylight, are June 6 to 16 and June 29 to July 12, with a “cutout” of July 2 to 4, when a launch would not be possible.
The Artemis-1 mission will be the first uncrewed integrated flight test of NASA’s Orion spacecraft and Space Launch System rocket. The SLS rocket is designed for missions beyond low-Earth orbit carrying crew or cargo to the Moon and beyond. At liftoff, it will weigh approximately six million pounds (~2700 tons) and produce around 8.8 million pounds (~4000 tons) of thrust.
News
Tesla is preparing to take on autonomy’s final boss
India’s city streets are notorious for their complexity and congestion.

If there is any sign that Tesla is now confident about its self-driving program, it would be this. As could be seen on Tesla’s Careers page, the company is now hiring Autopilot Vehicle Operators in Delhi and Mumbai, India.
As far as real-world traffic is concerned, one could argue that India’s city streets are the final boss of autonomous driving systems due to their complexity and congestion.
Tesla job openings
As per Tesla in its recent job openings, Prototype Vehicle Operators will be responsible for driving an engineering vehicle for extended periods and conducting dynamic audio and camera data collection for testing and training purposes. In both its job listings for Mumbai and Delhi, Tesla noted that successful applicants will be gathering real-world data on the weekends and around the clock.
Considering the job openings in India, Tesla seems to be intent on rolling out its advanced driver-assist systems like FSD in the country. This is quite interesting, as Tesla is not hiring Prototype Vehicle Operators in other territories that recently launched, such as the Philippines. Perhaps Tesla intends to tackle FSD’s final boss of sorts before rolling out FSD in other territories.
FSD’s rollout
Tesla’s autonomous driving program uses the company’s Full Self-Driving system, which is currently available on vehicles in North America and China. Tesla, however, has a more advanced version of FSD called Unsupervised FSD, which is currently being used in vehicles that are part of the Robotaxi pilot in Austin and the Bay Area.
Elon Musk has also recently announced on X that Tesla will be releasing FSD V14 in the coming weeks. He also shared a number of improvements that can be expected from FSD V14. “The FSD release in about 6 weeks will be a dramatic gain with a 10X higher parameter count and many other improvements. It’s going through training & testing now. Once we confirm real-world safety of FSD 14, which we think will be amazing, the car will nag you much less,” Musk wrote in his post.
News
Tesla Sweden finally makes IF Metall union give up 600-day strike
Tesla and the union have opened the door to resolutions that do not involve a collective agreement.

After nearly two years of industrial action and sympathy strikes, Swedish labor union IF Metall has stated that it is softening its stance in its dispute with Tesla. With this, Tesla and the union have opened the door to resolutions that do not involve a collective agreement.
Union chair Marie Nilsson told Sveriges Radio’s Ekot that while the preferred outcome remains a signed agreement, “other alternative solutions” are now on the table.
Union reconsiders rigid demands
The strike, which began over 600 days ago, has been marked by a series of strategic moves from both sides. IF Metall blocked Tesla’s access to license plates by targeting mail delivery, while Tesla bypassed the restrictions by importing vehicles in bulk through German ferries to Trelleborg, among other strategies.
Despite the high-profile tactics, the number of active strikers has been relatively small, just about 60 in total, as noted in a CarUp report. Tesla Sweden has also maintained that it does not intend to bow down to the union’s demands. Over the 600-day strike, Tesla Sweden has adapted its operations to get around the union and its allies’ strikes.
Possible paths to ultimate resolution
Nilsson, for her part, noted that IF Metall is now willing to explore alternatives, such as embedding industry-standard terms directly into Tesla’s employment contracts or shifting Tesla’s Swedish operations to a company that already has a collective agreement.
“You can do it in different ways. The easiest thing would be to sign a collective agreement. But when that is not possible, we have to find other alternative solutions as well, so we are open to discussion,” Nilsson stated.
IF Metall, if any, has acknowledged that Tesla has already improved working conditions in Sweden since the dispute began. Tesla Sweden has argued that its working conditions are already better than union standards, which is reportedly one of the reasons why very few company employees actually participated in IF Metall’s strike.
“There have been conversations throughout the journey where we compared our conditions. Tesla has adjusted details without going into details, they want to be a good employer, it’s about wages and conditions,” Nilsson stated.
Cybertruck
Tesla Cybertruck is getting a big security upgrade
“Cybertruck was not 100% carryover in execution like S3XY, so it required work.”

Tesla confirmed today that a massive Cybertruck security feature is on the way soon, and it is one that owners have been asking about for a long time.
Like all Teslas, Cybertruck has the excellent security feature known as “Sentry Mode.” The feature essentially turns your Tesla into a moving security camera, recording any event that happens nearby.
It has been used to solve crimes such as vandalism and burglary, and even used by police departments to solve other, high-profile crimes.
Tesla quietly added this extra Sentry Mode feature to deter vandals
However, Cybertruck has been missing one key feature of Sentry Mode: the use of the B-Pillar camera has not been enabled, leaving one of the most vandalized and targeted vehicles in the United States with a weakness.
One person who has been vocal about it is Tesla Cybertruck enthusiast Greggertruck, who has been pushing for answers for months. He finally got his answer from Cybertruck Vehicle Program Manager Siddhant Awasthi:
“It will come soon! Cybertruck was not 100% carryover in execution like SX3Y so it required work. Team has finished work on this and just need to make sure it’s validated and runs reliably (which it should for its feature).”
It will come soon! Cybertruck was not 100% carryover in execution like SX3Y so it required work. Team has finished work on this and just need to make sure it’s validated and runs reliably (which it should for its feature)
— Siddhant Awasthi (@siddawa) August 14, 2025
It sounds as if Tesla’s issue was something they similarly experienced when deploying Full Self-Driving to Cybertruck. The other four Tesla vehicles were able to use FSD because they’re all relatively similar in ride height and overall functionality. They share tons of similarities.
Cybertruck did not get FSD right away because Tesla still had to work on the differences between it and the other cars in the lineup. As Awasthi said, “Cybertruck was not 100% carryover in execution like S3XY, so it required work.”
Tesla Cybertruck FSD release expected for Sept, Park Assist to come first
It sounds as if Tesla is close to resolving some of the more intricate details of adding the functionality, and it was just a matter of time before it figured out the issue.
The release of the B-Pillar camera being active during Sentry Mode events on Cybertruck will likely come in a software update in the coming weeks.
-
Elon Musk1 week ago
Elon Musk teases crazy new Tesla FSD model: here’s when it’s coming
-
Elon Musk6 days ago
Elon Musk confirms Tesla AI6 chip is Project Dojo’s successor
-
News6 days ago
Tesla Model Y L reportedly entered mass production in Giga Shanghai
-
Elon Musk1 week ago
Tesla CEO Elon Musk details massive FSD update set for September release
-
Cybertruck6 days ago
Tesla’s new upgrade makes the Cybertruck extra-terrestrial
-
News4 days ago
Elon Musk reaffirms Tesla Semi mass production in 2026
-
Elon Musk1 week ago
Tesla ‘activist shareholders’ sue company and Elon Musk for Robotaxi rollout
-
News1 week ago
Elon Musk explains why Tesla stepped back from Project Dojo