Connect with us

News

SpaceX preparing giant crane to assemble Starship’s first Florida launch tower

SpaceX has begun staging parts of a massive crane it needs to stack Starship's first Florida 'launch tower.' (@StarshipGazer)

Published

3 years ago

on

SpaceX has begun staging and assembling parts of a giant crane it will soon need to stack Starship’s first East Coast launch tower and install other major launch pad components.

The presence of the base of that crane at SpaceX’s NASA Kennedy Space Center (KSC) Launch Complex 39A was visually confirmed by NASASpaceflight.com photographers during a weekly aerial tour of the area on June 3rd. Four days later, Teslarati photographer Richard Angle observed more major crane components on their way to Pad 39A, including the crane’s cabin.

More likely than not, the crane SpaceX or its contractor has begun assembling at 39A is a Liebherr LR 11350, the same kind of crane the company used to assemble Starship’s first orbital launch site and tower in South Texas. In fact, given how few LR 11350s there are in existence, it’s entirely possible that it’s the exact same crane. Assembly of that crane began around April 2021 and took a month and a half, at which point it was finally ready to lift an extended boom long enough to assemble a tower almost 500 feet (~150 meters) tall.

Part of SpaceX’s massive LR 11350 crane is visible on the right. (NASASpaceflight – bocachicagal)

Pad 39A’s Starship launch tower is expected to be very similar to Starbase’s, although it will undoubtedly carry over numerous design changes thanks to lessons learned while building and outfitting the first tower. In fact, SpaceX has already assembled five of the nine individual sections that will eventually be stacked to form that tower, and one such change is already obvious. Instead of stacking each tower section as soon as its barebones framework is complete, SpaceX is taking a more methodical approach to its second launch tower. In an apparent attempt to limit the amount of work that needs to be done at Pad 39A itself, each of those segments is being thoroughly outfitted with secondary structures (ladders, doors, walkways, frames, raceways, etc.) before stacking.

SpaceX may even pre-install most of the thousands of feet of plumbing needed to connect a Starship to ground systems located around 90 meters (~300 ft) below it. Once stacked, each section – including all those partial propellant and gas lines – will still need to be joined together, but that process should be far easier than fully installing all the systems the tower needs to do its job. Outfitting Starbase’s launch tower, for example, took SpaceX around half a year and, to some extent, is still ongoing 11 months after the final stack. That likely explains why Starship’s 39A tower section assembly appears to be taking more time. With any luck, partially combining the outfitting and section assembly stages will significantly expedite final assembly, as far less work will need to be done at extreme heights or require a skyscraper-sized crane.

SpaceX’s Starship launch tower was stacked to its full height on July 28th. (@StarshipGazer)

Through Starbase, SpaceX has already demonstrated the ability to stack a Starship launch tower from its unoccupied concrete base to its final height of ~145 meters (~475 ft) in about two months flat. While SpaceX will have to slalom its way around Pad 39A’s busy launch manifest, there’s no reason to believe that Starship’s first Florida launch tower won’t be stacked at least as quickly.

Aside from the arrival of crane parts, SpaceX has also made great progress on the Starship launch site itself. In the last few weeks, the company appears to have completed several significant concrete pours on the tower base. SpaceX has also installed all six of the pedestal-like orbital launch mount’s legs after months of foundation work. Elsewhere at Cape Canaveral, a different team has made excellent progress assembling the massive donut-like platform that will sit on top of those legs. Due to its extreme weight (possibly around 300 metric tons, per Elon Musk’s comments on the Starbase mount), the same LR 11350 crane will also be needed for that major installation milestone.

Advertisement
Starbase’s orbital launch mount. Starship’s Florida mount has incorporated many design changes. (NASASpaceflight – bocachicagal)

Plenty of parts are still missing, of course. Four tower sections still need to be assembled. Starship’s first Florida launch tower will need its own set of two ‘chopstick’ arms for lifting and (maybe) catching Starship and Super Heavy, as well as a third swinging quick-disconnect arm to connect Starship to ground systems. Aside from delivering several new tanks, SpaceX has also made no apparent progress on adding a massive methane propellant farm to Pad 39A, and it’s possible that the pad’s oxygen farm will also need to be expanded. Propellant storage has proven to be a major headache for SpaceX at Starbase.

Nonetheless, SpaceX is making great progress on most of the most difficult parts of Starship’s first Florida launch site, and there’s a good chance that just like its launch mount, work on the pad’s tower arms is already underway somewhere offsite. A great deal of work remains to be done but SpaceX is still well on its way to launching Starships out of Kennedy Space Center in the not-too-distant future.

Related Topics:

Eric Ralph is Teslarati's senior spaceflight reporter and has been covering the industry in some capacity for almost half a decade, largely spurred in 2016 by a trip to Mexico to watch Elon Musk reveal SpaceX's plans for Mars in person. Aside from spreading interest and excitement about spaceflight far and wide, his primary goal is to cover humanity's ongoing efforts to expand beyond Earth to the Moon, Mars, and elsewhere.

Advertisement
Comments

News

Tesla appears to be mulling a Cyber SUV design

In a new video titled “Sustainable Abundance,” Tesla was showing the Cybercab clay models being autonomously molded. In the back, there are very clearly several models of a Cybertruck-inspired SUV:

Published

15 hours ago

on

September 1, 2025

By

Credit: Tesla

Tesla appears to be mulling a Cyber SUV design, which would encapsulate the stainless steel exoskeleton of the Cybertruck but with elements of an SUV.

The company has been hearing from consumers and fans for some time that it is in need of a full-size SUV in its lineup.

Tesla is missing one type of vehicle in its lineup and fans want it fast

The Model X is more compact than what people are looking for, and although the company has said its focus for some time would be on developing affordable models and the Cybercab, which only enables two-passenger travel, it appears that it may be considering other options.

In a new video titled “Sustainable Abundance,” Tesla was showing the Cybercab clay models being autonomously molded. In the back, there are very clearly several models of a Cybertruck-inspired SUV:

This would not be the first time Tesla has placed projects it is developing in the back of a promotional video, as it did something similar when it was unveiling the improvements it made to the new Model Y earlier this year.

It appeared to show two new body styles sitting in the back under car covers:

 

View this post on Instagram

 

A post shared by TESLARATI (@teslarati)

There are two things that could prevent this from becoming a future, developed product that reaches the market. One of them seems to be a definitive no, but Tesla’s plans could certainly change, especially given the strong push from fans for this type of vehicle.

Tesla said it wouldn’t build a Stainless Steel exoskeleton vehicle again

Tesla said in its Q4 2024 Shareholder Deck that Cybertruck’s stainless steel exoskeleton would not be used in future vehicles in the top line:

This seems like a definitive no in terms of developing an SUV based on Cybertruck’s aesthetics. However, that could always change.

Tesla’s main focus in autonomy currently

Developing an SUV of this size has been previously dismissed by Tesla, as its focus is on autonomy, AI, and robotics. However, it will still need to develop attractive and useful vehicles that address a large market, and the United States has a strong affinity for SUVs and crossovers.

It seems totally feasible that Tesla could bring this type of vehicle to market to appease the many fans who have called for the company to build it. Tesla has not committed to anything at this point, which is the most important thing to remember.

Continue Reading

News

Tesla receives European Ecolabel (EMAS) seal for Giga Berlin-Brandenburg

The EMAS seal highlights Tesla’s existing environmental measures in the facility.

Published

22 hours ago

on

September 1, 2025

By

Credit: Tesla/X

Tesla has been awarded the European Ecolabel (EMAS) seal for Gigafactory Berlin-Brandenburg. 

The EMAS seal highlights Tesla’s existing environmental measures in the facility, such as extensive reforestation efforts and reduced water usage. It also emphasizes Tesla’s commitment to improve its environmental initiatives.

Giga Berlin’s environmental initiatives

The EMAS (Eco-Management and Audit Scheme) seal is a long-term environmental management system that focuses on compliance with regulations and improving environmental performance, as noted in a Tagesspiegel report.

Plant manager André Thierig noted that Tesla has already planted over 2 million trees to replace the trees that have been felled to make way for Giga Berlin. Tesla is also targeting an additional 5 to 15 MW peak solar capacity this year to make the plant more sustainable. “We will continue to promote photovoltaics in the future,” he said.

Giga Berlin’s consumption and energy use

In 2024, Giga Berlin consumed about 419,503 MWh of energy, with electricity accounting for more than half, followed by natural gas. The facility is looking to lower natural gas use by redirecting the use of process heating water via waste heat. Water consumption was listed at 2.16 cubic meters per vehicle, significantly below the industry average of 3.5.

Advertisement

This year, Tesla Giga Berlin is looking to recycle 90% of the Model Y plant’s process wastewater. Around 11,000 employees currently work at Giga Berlin, which produces 5,000 vehicles per week or roughly 250,000 units annually.

Certification welcomed but not without criticism

The EMAS program requires companies to disclose resource use, emissions, and improvement plans. Over 40 companies in Brandenburg have EMAS certification.

Brandenburg’s Environment Minister Minister Hanka Mittelstädt (SPD) described Tesla as a role model for the region. “Everything is public, and that also creates a certain amount of trust,” she said, noting that Tesla is a “beacon” in the industry.

Monique Zweig, Managing Director of the East Brandenburg Chamber of Industry and Commerce (IHK), shared her optimism in a comment to rbb24. “At Tesla, you can see that climate goals go hand in hand with industry,” Zweig stated.

Unsurprisingly, local activists expressed skepticism. The Association for Nature and Landscape in Brandenburg, which is against Tesla, questioned whether the certification could be used as “greenwashing.”

Advertisement

The group also alleged that the certificate could pave the way for weaker oversight for the EV maker. “The seal is ‘greenwashing’ to portray the company as more environmentally friendly,” spokesperson Steffen Schorcht noted.

Continue Reading

News

I traded my ICE vehicle for a Tesla Model Y: here’s how it went

After working at Teslarati for six years and covering the EV space nearly every single day (I recently published my 5,000th article on here), I figured it was time to make a switch.

Published

23 hours ago

on

September 1, 2025

By

I recently decided, after a variety of things, that I was going to trade in my internal combustion engine (ICE) vehicle for a new Tesla Model Y. It was a long time coming.

After working at Teslarati for six years and covering the EV space nearly every single day (I recently published my 5,000th article on here), I figured it was time to make a switch. Over the past few years, there have been days when I would have been better off with an EV, but my Summer and Winter activities, as well as the price, kept me from making the switch.

Recently, I decided that it was time. My 2021 Ford Bronco Sport had been experiencing a number of issues, none major, but numerous sensor replacements. It was an affordable and fun car, but after fixing the Tire Pressure Monitoring System in the front right tire, an EVAP switch valve in the motor two months ago, and some other things, the Bronco became more of a chore (and a drain on my wallet) than anything.

With the timing of the $7,500 tax credit expiring and a substantial amount of positive equity in my Bronco, I knew it was time. My experience was excellent, but I would like to share some insights with our readers about the entire process, which may also help you make the jump. Others were more of a one-time thing, as they were things customers would only deal with as the tax credit went away.

My Decision

I knew I was going to get a Tesla, and my inability to enjoy a good sedan steered me to a Model Y (no hate toward the Model 3, it’s just not for me). I knew with the weather in Pennsylvania, all-wheel drive was a need, and the price difference between the rear-wheel-drive and AWD configurations of the Y made it a no-brainer.

Plus, I really would like to get this thing out on the beach, something I’ve done every Summer since buying the Bronco with my Fiancè.

I actually ordered this car back in June, but ended up canceling the reservation to wait until the end of Summer. I ended up ordering the car I took delivery of on Saturday back on my birthday on August 16.

I was looking for Diamond Black with White Interior, and it was available in Pittsburgh for delivery. However, I really love the team at Tesla Mechanicsburg, so I opted to do a Black on Black Model Y that was a Fremont build, so I could pick it up from the guys up there. The interior color was not a dealbreaker for me. I just wanted to take delivery soon.

I ordered from inventory, which is not something that is possible now. There is no new Model Y inventory within 200 miles of me, a good sign for Tesla but a bad sign if you’re looking to buy something before the quarter ends. Luckily, the IRS is allowing people to enter an agreement for a car, so you could technically build the car of your choice, put a down payment on it, and take delivery after the September 30 cutoff.

Tesla Delivery Day

My appointment was at 12 p.m. and I arrived about ten minutes before. The team greeted me quickly, and I was able to walk right up and see my car with my name on it. It was pretty incredible and a feeling I have not felt in a long time. I’ll be honest, when I bought the Bronco, I never thought I’d own one. When I got one, it felt pretty surreal.

I felt that way yesterday. It was really cool to finally buy a car that I’d only dreamed of owning. It’s not the only car I dream of owning in my lifetime, but it is one I knew I wanted right now. Now that I was showing up to buy it, it really felt surreal.

The process was really fast and efficient, and I could have been in and out in ten minutes if I wanted to. However, I hung around and talked to the guys there; they discussed some good accessories I should consider and suggested some tint.

I was on my way.

My First Drive and What to Expect

I stopped by my Fiancè’s work, showed her the new ride, brought her some lunch, and headed home to my pup. So far, I’ve driven about 60 miles, with most of it being done manually and about 10 miles using Full Self-Driving. I’ve enjoyed driving it myself so much as of right now, but I know FSD will come in handy plenty in the coming months.

In the future, I plan to explore a wide range of topics as an owner. I do not currently have home charging, which is something that many people believe is a dealbreaker for owning an EV. I have two Superchargers very close to my place, so I’m not too concerned about it.

I have been in touch with my leasing office about installing a charger or chargers for the past few months, which seems like it could happen early next year.

So far, I’m really happy with how everything has worked out.

Continue Reading

Trending