News
Tesla Cybercab spotted with interesting charging solution, stimulating discussion
The port is located in the rear of the vehicle and features a manual door and latch for plug-in, and the video shows an employee connecting to a Tesla Supercharger.
Tesla Cybercab units are being tested publicly on roads throughout various areas of the United States, and a recent sighting of the vehicle’s charging port has certainly stimulated some discussions throughout the community.
The Cybercab is geared toward being a fully-autonomous vehicle, void of a steering wheel or pedals, only operating with the use of the Full Self-Driving suite. Everything from the driving itself to the charging to the cleaning is intended to be operated autonomously.
But a recent sighting of the vehicle has incited some speculation as to whether the vehicle might have some manual features, which would make sense, but let’s take a look:
🚨 Tesla Cybercab charging port is in the rear of the vehicle!
Here’s a great look at plugging it in!!
— TESLARATI (@Teslarati) January 29, 2026
The port is located in the rear of the vehicle and features a manual door and latch for plug-in, and the video shows an employee connecting to a Tesla Supercharger.
Now, it is important to remember these are prototype vehicles, and not the final product. Additionally, Tesla has said it plans to introduce wireless induction charging in the future, but it is not currently available, so these units need to have some ability to charge.
However, there are some arguments for a charging system like this, especially as the operation of the Cybercab begins after production starts, which is scheduled for April.
Wireless for Operation, Wired for Downtime
It seems ideal to use induction charging when the Cybercab is in operation. As it is for most Tesla owners taking roadtrips, Supercharging stops are only a few minutes long for the most part.
The Cybercab would benefit from more frequent Supercharging stops in between rides while it is operating a ride-sharing program.
Tesla wireless charging patent revealed ahead of Robotaxi unveiling event
However, when the vehicle rolls back to its hub for cleaning and maintenance, standard charging, where it is plugged into a charger of some kind, seems more ideal.
In the 45-minutes that the car is being cleaned and is having maintenance, it could be fully charged and ready for another full shift of rides, grabbing a few miles of range with induction charging when it’s out and about.
Induction Charging Challenges
Induction charging is still something that presents many challenges for companies that use it for anything, including things as trivial as charging cell phones.
While it is convenient, a lot of the charge is lost during heat transfer, which is something that is common with wireless charging solutions. Even in Teslas, the wireless charging mat present in its vehicles has been a common complaint among owners, so much so that the company recently included a feature to turn them off.
Production Timing and Potential Challenges
With Tesla planning to begin Cybercab production in April, the real challenge with the induction charging is whether the company can develop an effective wireless apparatus in that short time frame.
It has been in development for several years, but solving the issue with heat and energy loss is something that is not an easy task.
In the short-term, Tesla could utilize this port for normal Supercharging operation on the Cybercab. Eventually, it could be phased out as induction charging proves to be a more effective and convenient option.
Elon Musk
Tesla showcases Optimus humanoid robot at AWE 2026 in Shanghai
Tesla’s humanoid robot was presented as part of the company’s exhibit at the Shanghai electronics show.
Tesla showcased its Optimus humanoid robot at the 2026 Appliance & Electronics World Expo (AWE 2026) in Shanghai. The event opened Thursday and featured several Tesla products, including the company’s humanoid robot and the Cybertruck.
The display was reported by CNEV Post, citing information from local media outlet Cailian and on-site staff at the exhibition.
Tesla’s humanoid robot was presented as part of the company’s exhibit at the Shanghai electronics show. On-site staff reportedly stated that mass production of the robot could begin by the end of 2026.
Tesla previously indicated that it plans to manufacture its humanoid robots at scale once production begins, with its initial production line in the Fremont Factory reaching up to 1 million units annually. An Optimus production line at Gigafactory Texas is expected to produce 10 million units per year.
Tesla China previously shared a teaser image on Weibo showing a pair of highly detailed robotic hands believed to belong to Optimus. The image suggests a design with finger proportions and structures that closely resemble those of a human hand.
Robotic hands are widely considered one of the most difficult engineering challenges in humanoid robotics. For a system like Optimus to perform complex real-world tasks, from factory work to household activities, the robot would require highly advanced dexterity.
Elon Musk has previously stated that Optimus has the capability to eventually become the first real-world example of a Von Neumann machine, a self-replicating system capable of building copies of itself, even on other planets. “Optimus will be the first Von Neumann machine, capable of building civilization by itself on any viable planet,” Musk wrote in a post on X.
Elon Musk
Tesla Cybercab production line is targeting hundreds of vehicles weekly: report
According to the report, Tesla has been adding staff and installing new equipment at its Austin factory as it prepares to begin Cybercab production.
Tesla is reportedly designing its Cybercab production line to manufacture hundreds of the autonomous vehicles each week once mass production begins. The effort is underway at Gigafactory Texas in Austin as the company prepares to start building the Robotaxi at scale.
The details were reported by The Wall Street Journal, citing people reportedly familiar with the matter.
According to the report, Tesla has been adding staff and installing new equipment at its Austin factory as it prepares to begin Cybercab production.
People reportedly familiar with Tesla’s plans stated that the company has been growing its staff and bringing in new equipment to start the mass production of the Cybercab this April.
The Cybercab is Tesla’s upcoming fully autonomous two-seat vehicle designed without a steering wheel or pedals. The vehicle is intended to operate primarily as part of Tesla’s planned Robotaxi ride-hailing network.
“There’s no fallback mechanism here. Like this car either drives itself or it does not drive,” Musk stated during Tesla’s previous earnings call.
Tesla has indicated that Cybercab production could begin as soon as April, though Elon Musk has noted that early production will likely be slow before ramping over time. Musk has stated that the Cybercab’s slow ramp is due in no small part to the fact that it is a completely new vehicle platform.
Tesla’s Cybercab is designed to work with the company’s Full Self-Driving (FSD) system and support its planned autonomous ride-hailing service. The company has suggested that the vehicle could cost under $30,000, making it one of Tesla’s most affordable models if produced at scale. Musk has confirmed in a previous X post that the vehicle will indeed be offered to regular consumers at a price below $30,000.
Musk has previously stated that Tesla could eventually produce millions of Cybercabs annually if demand and production capacity scale as planned.
News
Tesla VP explains latest updates in trade secret theft case
Tesla reportedly caught Matthews copying the tech into machines that were sold to competitors, claiming they lied about doing so for three years, and continued to ship it. That is when Tesla chose to sue Matthews in July 2024 in Federal court, demanding over $1 billion in damages due to trade secret theft.
Tesla Vice President Bonne Eggleston explained the latest updates in a trade secret theft case the company has against a former manufacturing equipment supplier, Matthews International.
Back in 2024, Tesla had filed a lawsuit against Matthews International, alleging that the firm stole trade secrets about battery manufacturing and shared those details with some of Tesla’s competitors.
Early last year, a U.S. District Court Judge denied Tesla’s request to block Matthews International from selling its dry battery electrode (DBE) technology across the world. The judge, Edward Davila, said that the patent for the tech was due to Matthews’ “extensive research and development.”
The two companies’ relationship began back in 2019, as Tesla hired Matthews to help build the equipment for its 4680 battery cell. Tesla shared confidential software, designs, and know-how under strict secrecy rules.
Fast forward a few years, and Tesla reportedly caught Matthews copying the tech into machines that were sold to competitors, claiming they lied about doing so for three years, and continued to ship it. That is when Tesla chose to sue Matthews in July 2024 in Federal court, demanding over $1 billion in damages due to trade secret theft.
Now, the latest twist, as this month, a Judge issued a permanent injunction—a court order banning Matthews from using certain stolen Tesla parts or designs in their machines. Matthews is also officially “liable” for damages. The exact amount would still to be calculated later.
Bonne Eggleston, a VP for Tesla, said on X today that Matthews is a supplier who “exploited customer IP through theft or deception,” and has no place in Tesla’s ecosystem:
Buyer beware: Matthews International stole Tesla’s DBE technology and is now subject to an injunction and liable for damages.
During our work with Matthews, we caught them red-handed copying our technology—including proprietary software and sensitive mechanical designs—into… https://t.co/Toc8ilakeM
— Bonne Eggleston (@BonneEggleston) March 10, 2026
Tesla calls this a big win and warns other companies: “Buyer beware—don’t buy from thieves.”
Matthews hit back with a press release claiming victory. They say an arbitrator ruled they can keep selling their own DBE equipment to anyone and rejected Tesla’s request for a total sales ban. They call Tesla’s claims “nonsense” and insist their 20-year-old tech is independent. Both sides are spinning the same narrow ruling: Matthews can sell their version, but they’re blocked from using Tesla’s specific secrets.
What are Tesla’s Current Legal Options
The case isn’t over—it’s moving to the damages phase. Tesla can:
- Push forward in court or arbitration to calculate and collect huge financial penalties (potentially $1 billion+ if willful theft is proven).
- Enforce the permanent injunction with contempt charges, fines, or even jail time if Matthews violates it.
- Challenge Matthews’ new patents that allegedly copy Tesla’s work, asking courts to invalidate them or add Tesla as co-inventor.
- Seek extra damages, lawyer fees, and possibly punitive awards under the federal Defend Trade Secrets Act and California law.
Tesla could also refer evidence to federal prosecutors for possible criminal trade-secret charges (rare but serious). Settlement is always possible, but Tesla’s fiery public response suggests they want full accountability.
This isn’t just corporate drama. It shows why trade secrets matter even when Tesla open-sources some patents, confidential know-how shared in trust must stay protected. For the EV industry, it’s a reminder: steal from your biggest customer, and you risk losing everything.
Tesla showcases Optimus humanoid robot at AWE 2026 in Shanghai
Tesla Cybercab production line is targeting hundreds of vehicles weekly: report
