News
SpaceX’s first Starlink V2 satellites spotted at Starbase
On Monday, SpaceX was spotted loading some of the first Starlink V2 satellite prototypes into a custom mechanism designed to refill Starship’s magazine-like payload bay.
While it’s not the first time SpaceX has used the dispenser, the photos captured by photographer Kevin Randolph for the YouTube channel ‘What about it!?’ are the first to clearly show real prototypes of the next generation of Starlink satellites. According to CEO Elon Musk, those Starlink Gen2 or V2 satellites will be “at least 5 times better”, “an order of magnitude more capable,” and about four times heavier than current (V1.5) Starlink satellites.
The potential of the new satellite bus design paired with Starship’s massive fairing and lift capacity could dramatically improve the viability and cost-effectiveness of SpaceX’s Starlink constellation. First, though, the company needs to launch and qualify prototypes of the new satellite design and verify that all associated ground support equipment works as expected.
Due to the designs SpaceX has settled on for both Starlink V2.0 satellites and the Starship hardware that will deploy them in orbit, that ground support equipment and the general path each satellite will take from its arrival at the launch facilities to liftoff on a Starship are wildly different than anything done before. July 18th’s photos (and screenshots from a recent factory tour) confirm that the next-gen satellites are basically enlarged versions of their smaller predecessors, which are also narrow rectangles.
The new spacecraft have a very similar aspect ratio but are around seven meters long and three meters wide (23′ x 10′) instead of approximately 3m x 1.5m (10′ x 5′). They also appear to be about twice as thick and reportedly weigh ~1,250 kilograms to V1.5’s estimated 310 kilograms (~2,750 lb vs ~680 lb). As a result, the V2.0 bus will have about 7-10 times more usable volume than V1.0 and V1.5. It should be no surprise, then, that each next-gen satellite could offer almost magnitude more usable bandwidth.
Assuming that Starship launch costs are roughly the same as Falcon 9 and that Starship can only launch a similar 50-60 satellites at once, an almost 10x performance improvement from a satellite that only weighs five times as much relative to V1.5 would make Starlink V2.0 constellation deployment at least twice as cost-efficient to deploy even if Starship could only launch the same mass (~16 tons) as Falcon 9. In fact, a recent SpaceX render suggests that Starship will be able to carry 54 Starlink V2.0 satellites initially. As a result, even if Starship costs five times more to launch than Falcon 9 (~$75M), it will still be cheaper per unit of bandwidth launched. If Starship eventually reaches marginal launch costs as low as Falcon 9 (~$15M), the cost of Starlink launches (not including satellite cost) could plummet from about $15,000 per gigabit per second (Gbps) to around $1,500-2,500 per Gbps depending on individual satellite bandwidth.
The total cost of the network will be higher, of course, and dependent on more variables, but the combination of Starship and V2.0 satellites could eventually reduce the relative cost of Starlink launch operations by a factor of 5-10. If Starlink V2.0 satellites are actually cheaper to manufacture per unit of throughput than V1.5 satellites, which is not implausible once mass-production begins, those savings will deepen. If Starship can quickly mature and becomes fully and efficiently reusable, the equation could become even more favorable.
Still, loading Starship with satellites is going to be no minor feat and will add a significant amount of complexity and risk relative to the methods SpaceX currently uses for Falcon 9 Starlink launches. SpaceX’s initial Starship payload bay design is a roughly square enclosure that slots just above the ship’s uppermost tank dome and below its inward-curving nosecone. Per a render of the mechanism released last month, it measures about nine meters (30 ft) tall and eight meters (26 ft) wide, can store up to 54 Starlink V2.0 satellites, and dispenses pairs of satellites through a relatively tiny payload bay door that’s only wide enough for the task at hand.
Starship’s airframe is almost exclusively welded together. Once the nosecone and payload bay are installed on top of a ship, the only way to access the interior of the bay is through the dispenser door or an even smaller human-sized access port. SpaceX’s solution: build a mobile satellite storage box that will be lifted by crane (or launch tower arms) dozens to hundreds of feet off the ground and use the payload bay’s own dispenser mechanism in reverse to load satellites like bullets into a giant magazine. If that sounds simple, which it shouldn’t, it’s not.
It’s great, then, to see SpaceX apparently practicing that process with some of the first Starlink V2.0 prototypes. In photos captured on July 18th, workers were spotted loading several satellites into the only existing ‘loader’ inside one of Starbase’s three main factory tents. Each satellite was lifted using a load-spreader device that was presumably required to prevent the extremely long and thin satellites from bending too much in the middle during the lift. It’s unclear whether SpaceX is solely practicing the process or if it’s actually installing satellites well in advance for loading onto a Starship prototype.
Starship S24 is in the middle of preflight testing and has already been greeted by the satellite loader once before, possibly to load a prototype or mockup before ground testing began. Starship S25 appears to be at least a month or two away from completion, though its nose and payload bay section are much closer.
Tesla has officially revealed its 2026 Summer Update, which comes with a variety of crazy new features, including Navigation fixes that owners have been wanting for months.
Tesla routinely releases a larger update with the Spring, Summer, Fall, and Winter updates, where it ships a variety of new features, bug fixes, and other additions to customer cars.
The 2026 Spring Update featured things like “Hey Grok” voice assistance, a redesigned self-driving app, Unreal Engine visual upgrades, and more.
🚨 TESLA’S SUMMER UPDATE FOR 2026 IS HERE:
Featuring:
✅ Self-Driving Stats in Mobile App
✅ Caraoke with Scoring
✅ Automatic Navigation
✅ Preferred Routes
✅ Set Arrival Energy from Mobile App
✅ Send Custom Wraps from Mobile App
✅ Rear Display Lock
✅ Other Improvements
🔌… https://t.co/C9IW3egEhH
— TESLARATI (@Teslarati) July 21, 2026
Tesla’s Summer Release has about ten new features; we’ll show you each and detail them below:
New Grok Voice Commands
“Grok can now make phone calls, search and play music, adjust climate, open the glovebox, and answer questions about your Tesla.”
Self-Driving Stats in Mobile App
“View and share self-driving stats from the mobile app.”
Caraoke With Scoring
“Caraoke now scores your singing while in Park. High scores are saved to your Tesla profile.”
Automatic Navigation
“Automatic Navigation now adapts to your routine.
In addition to Home, Work, and upcoming calendar events, your vehicle can now suggest and route to places you visit regularly – like a school drop-off on the way to work, or the gym on the way home.”
Preferred Routes
“For a more personalized experience, navigation now prioritizes routes that you’ve taken before”
Set Arrival Energy from Mobile App
“Set your desired Arrival Energy from your phone.”
Send Custom Wraps from Mobile App
“Skip the USB drive and upload a custom wrap of your car from the mobile app. Instructions for creating a custom wrap here: https://github.com/teslamotors/custom-wraps.”
Rear Display Lock
“Kids can watch content on the rear screen, but only the front row can control it through the rear screen app.”
Other Improvements
- Find Superchargers by name when searching for a destination
- Add Apple Music songs to queue from search and artist page
- Set your preferred zoom level for the Self-Driving visualization
- Intro animations for new Model 3 and Y
Tesla’s reason for Starlink integration on Cybercab might surprise you, as the company’s Head of AI, Ashok Elluswamy, finally shed some light on the reason they are putting a satellite internet terminal on its ride-hailing-geared vehicle.
On Monday, Tesla officially confirmed that it would integrate Starlink V5 terminals into Cybercab vehicles, something many Tesla fans had figured the company would do, as the vehicle is primarily geared toward giving rides without any passenger intervention.
Starlink V5 directly integrated in Cybercab pic.twitter.com/FxzTtzjB6I
— Tesla (@Tesla) July 20, 2026
The ability to access the internet would allow riders to work or play in the car with their devices. It seemed like a more-than-reasonable feature to add to the Cybercab, which made its way off the production lines for the first time earlier this year.
Tesla reveals first vehicle model to receive Starlink integration
However, the move is not for the rider, as Elluswamy confirmed on Monday night. Instead, it’s actually for Tesla to be able to have a constant connection to the cars in the Robotaxi fleet so it can troubleshoot issues, contact riders, or resolve other issues.
Elluswamy said:
“It is still not required for safe operation of the vehicle. Connectivity is primarily meant for navigation, customer service and, in general, fleet management.”
It is still not required for safe operation of the vehicle. Connectivity is primarily meant for navigation, customer service and, in general, fleet management.
— Ashok Elluswamy (@aelluswamy) July 20, 2026
Many initially assumed the option of constant connectivity would be enabled on the Cybercab for passenger entertainment or work. With the Cybercab, passengers won’t be doing anything but enjoying the ride, so it seemed more than logical that they would be hanging out with Starlink internet access as an amenity.
However, Tesla’s primary concern with Robotaxi is safety, and nailing these first unsupervised rides is a crucial step to setting a good narrative on how effective driverless transportation can be.
Being able to get in touch with passengers or a vehicle if something is wrong is a crucial part of the overall experience, and preventative measures are being taken by Tesla to ensure a smooth process, even in the worst-case.
Tesla has expanded its Robotaxi program in Florida to include two new cities: Tampa and Orlando.
This marks the second and third cities to be added to the company’s available locations for autonomous ride-hailing in the Sunshine State, joining Miami, which was the first Florida city to offer Robotaxi rides.
Tesla announced the addition of Orlando and Tampa to the Robotaxi program on Tuesday morning. The cities now join Austin, Dallas, Houston, Miami, and the San Francisco Bay Area as locations where Tesla can operate its Robotaxi platform:
Robotaxi now in Tampa & Orlando! pic.twitter.com/fYtmXgJq3O
— Tesla Robotaxi (@robotaxi) July 21, 2026
These rides are unsupervised, as AI Head Ashok Elluswamy confirmed the suite in Florida is operating without safety drivers or anyone within the cabin to assist with operation.
Orlando Tesla Robotaxi Operation
The geofence in Orlando covers a prominent irregular shaded zone on the map, roughly 4-6 miles across in key dimensions, so it likely measures somewhere between 25 and 45 square miles, which is comparable to other early Tesla launches in other cities.
It encompasses central and southern areas bounded by major highways including SR-417 and SR-528, including parts of the Orlando metro core, tourism-adjacent zones, and residential/commercial districts. This represents an initial targeted rollout in a tourist-heavy region, positioned for quick expansion via Tesla’s software updates.
Tampa Tesla Robotaxi Operation
In Tampa, the shape of the geofence is a shaded polygon covering key neighborhoods, explicitly including West Tampa, Tampa Heights, Hyde Park, and downtown Tampa proper, with boundaries along major roads and the Hillsborough River area.
This focuses on high-demand central zones and will offer tourists and citygoers rides without drivers.
Robotaxi Progress
Tesla has been operating Robotaxi since last June, when it launched in Austin. The geofences in most regions have already expanded several times since their launch last year, but the bigger complaint is vehicle availability. Tesla has been working to add more Robotaxi-enabled vehicles to its fleet.
The company still plans to utilize its Cybercab, a new vehicle that is being produced at Gigafactory Texas, for the Robotaxi suite alongside the Model Y, which has been the vehicle of choice for Tesla with early operations.
Tesla reveals 2026 Summer Update with crazy fixes to Nav and more
Tesla’s reason for Starlink integration on Cybercab might surprise you
