Connect with us

News

Tesla Model 3 Highland manual gear selector is in a unique place

Credit: Tesla

Published

on

An immediate observation that could be observed from the Tesla Model 3 Highland is the fact that the all-electric sedan no longer features any physical stalks. This means that just like the Model S and Model X, the Model 3’s gear shifts would mostly be done through its infotainment display. 

This is quite intuitive, of course, considering Tesla’s mastery of in-vehicle software. Such a feature was received with much concern when it was rolled out to the Model S and Model X, with critics arguing that it would be cumbersome and unsafe. Over the years, however, complaints about the Model S and Model X’s in-display gear selector have all but disappeared. 

Credit: Tesla

Then again, one could argue that it would be okay for the Model S and Model X to use their infotainment system to shift their gears since the vehicles are equipped with multiple gear shifting options: Auto Shift, an in-display gear selector, and a manual gear selector beside the hazard button in the center console. The addition of Auto Shift has not been announced for the Model 3 Highland as of writing, but all demonstrations of the vehicle so far have featured drivers using the gear selector in the infotainment system. 

Credit: Tesla China

Fortunately, press images from Tesla, both from China and Europe, have revealed that the Model 3 Highland also has a contingency in the event that the in-display gear selector becomes unusable. As could be seen in images released by the company, a set of manual gear selectors is also included in the Model 3 Highland. Just like the Model S and Model X, the gear selectors in the Model 3 Highland flank the hazard button. 

Such a system may not be too much of an issue on the Model S and Model X since the hazard button on the flagship vehicles is on the center console. However, in the Model 3 Highland, the hazard button is located close to the rearview mirror. Thus, in the event that the Model 3 Highland’s in-display gear selector becomes inoperable, shifting gears manually will likely become an awkward, or at least cumbersome, experience. It would most definitely work, but its operation would not be very convenient or natural.

Don’t hesitate to contact us with news tips. Just send a message to simon@teslarati.com to give us a heads-up. 

Advertisement
-->

Simon is an experienced automotive reporter with a passion for electric cars and clean energy. Fascinated by the world envisioned by Elon Musk, he hopes to make it to Mars (at least as a tourist) someday. For stories or tips--or even to just say a simple hello--send a message to his email, simon@teslarati.com or his handle on X, @ResidentSponge.

Advertisement
Comments

News

Tesla Cybercab tests are going on overdrive with production-ready units

Tesla is ramping its real-world tests of the Cybercab, with multiple sightings of the vehicle being reported across social media this week.

Published

on

Credit: @JT59052914/X

Tesla is ramping its real-world tests of the Cybercab, with multiple sightings of the autonomous two-seater being reported across social media this week. Based on videos of the vehicle that have been shared online, it appears that Cybercab tests are underway across multiple states.

Recent Cybercab sightings

Reports of Cybercab tests have ramped this week, with a vehicle that looked like a production-ready prototype being spotted at Apple’s Visitor Center in California. The vehicle in this sighting was interesting as it was equipped with a steering wheel. The vehicle also featured some changes to the design of its brake lights.

The Cybercab was also filmed testing at the Fremont factory’s test track, which also seemed to involve a vehicle that looked production-ready. This also seemed to be the case for a Cybercab that was spotted in Austin, Texas, which happened to be undergoing real-world tests. Overall, these sightings suggest that Cybercab testing is fully underway, and the vehicle is really moving towards production.

Production design all but finalized?

Recently, a near-production-ready Cybercab was showcased at Tesla’s Santana Row showroom in San Jose. The vehicle was equipped with frameless windows, dual windshield wipers, powered butterfly door struts, an extended front splitter, an updated lightbar, new wheel covers, and a license plate bracket. Interior updates include redesigned dash/door panels, refined seats with center cupholders, updated carpet, and what appeared to be improved legroom.

There seems to be a pretty good chance that the Cybercab’s design has been all but finalized, at least considering Elon Musk’s comments at the 2025 Annual Shareholder Meeting. During the event, Musk confirmed that the vehicle will enter production around April 2026, and its production targets will be quite ambitious. 

Advertisement
-->
Continue Reading

News

Tesla gets a win in Sweden as union withdraws potentially “illegal” blockade

As per recent reports, the Vision union’s planned anti-Tesla action might have been illegal. 

Published

on

Andrzej Otrębski, CC BY-SA 4.0 , via Wikimedia Commons

Swedish union Vision has withdrawn its sympathy blockade against Tesla’s planned service center and showroom in Kalmar. As per recent reports, the Vision union’s planned anti-Tesla action might have been illegal. 

Vision’s decision to pull the blockade

Vision announced the blockade in early December, stating that it was targeting the administrative handling of Tesla’s facility permits in Kalmar municipality. The sympathy measure was expected to start Monday, but was formally withdrawn via documents sent to the Mediation Institute and Kalmar Municipality last week. 

As noted in a Daggers Arbete report, plans for the strike were ultimately pulled after employer group SKR highlighted potential illegality under the Public Employment Act. Vision stressed its continued backing for the Swedish labor model, though Deputy negotiation manager Oskar Pettersson explained that the Vision union and IF Metall made the decision to cancel the planned strike together.

“We will not continue to challenge the regulations,” Petterson said. “The objection was of a technical nature. We made the assessment together with IF Metall that we were not in a position to challenge the legal assessment of whether we could take this particular action against Tesla. Therefore, we chose to revoke the notice itself.”

The SKR’s warning

Petterson also stated that SKR’s technical objection to the Vision union’s planned anti-Tesla strike framed the protest as an unauthorized act. “It was a legal assessment of the situation. Both for us and for IF Metall, it is important to be clear that we stand for the Swedish model. But we should not continue to challenge the regulations and risk getting judgments that lead nowhere in the application of the regulations,” he said. 

Advertisement
-->

Vision ultimately canceled its planned blockade against Tesla on December 9. With Vision’s withdrawal, few obstacles remain for Tesla’s long-planned Kalmar site. A foreign electrical firm completed work this fall, and Tesla’s Careers page currently lists a full-time service manager position based there, signaling an imminent opening.

Continue Reading

News

Tesla Semi program Director teases major improvements

Published

on

Credit: Tesla

Tesla Semi Program Director Dan Priestly teased the major improvements to the all-electric Class 8 truck on Thursday night, following the company’s decision to overhaul the design earlier this year.

Priestley said he drove the Semi on Thursday, and the improvements appear to be welcomed by one of the minds behind the project. “Our customers are going to love it,” he concluded.

The small detail does not seem like much, but it is coming from someone who has been involved in the development of the truck from A to Z. Priestley has been involved in the Semi program since November 2015 and has slowly worked his way through the ranks, and currently stands as the Director of the program.

Tesla Semi undergoes major redesign as dedicated factory preps for deliveries

Tesla made some major changes to the Semi design as it announced at the 2025 Annual Shareholder Meeting that it changed the look and design to welcome improvements in efficiency.

Initially, Tesla adopted the blade-like light bar for the Semi, similar to the one that is present on the Model Y Premium and the Cybertruck.

Additionally, there are some slight aesthetic changes to help with efficiency, including a redesigned bumper with improved aero channels, a smaller wraparound windshield, and a smoother roofline for better aero performance.

All of these changes came as the company’s Semi Factory, which is located on Gigafactory Nevada’s property, was finishing up construction in preparation for initial production phases, as Tesla is planning to ramp up manufacturing next year. CEO Elon Musk has said the Semi has attracted “ridiculous demand.”

The Semi has already gathered many large companies that have signed up to buy units, including Frito-Lay and PepsiCo., which have been helping Tesla test the vehicle in a pilot program to test range, efficiency, and other important metrics that will be a major selling point.

Tesla will be the Semi’s first user, though, and the truck will help solve some of the company’s logistics needs in the coming years.

Continue Reading