News
SpaceX installs Starship Mk1 rocket’s flaps for the second time in build-up to flight debut
A little over a month after SpaceX CEO Elon Musk presented an update on Starship in Boca Chica, Texas and technicians dressed the rocket up for the show, SpaceX has begun to install Starship Mk1’s flaps for the second time.
This time, with any luck, those flaps are here to stay until Starship Mk1’s inaugural launch debut, an ambitious flight test with a target altitude of 20 km (12 mi).
Around the second half of September, SpaceX technicians appeared to begin working around the clock to fully assemble Starship, outfitting the exterior with the beginnings of plumbing, power lines, and avionics harnesses, stacking the Mk1 prototype’s two halves, and installing the vehicle’s large fore and aft flaps. During SpaceX CEO Elon Musk’s September 28th Starship update, what looked to be the largely finished Starship Mk1 served as the main backdrop – an undeniably impressive one, at that.
As would soon become clear, SpaceX’s September 2019 Starship Mk1 integration was actually more of a mock-assembly – all the parts involved appear to genuinely be real flight hardware, but almost all of it was only temporarily attached to Starship to give the partial appearance of a finished ship. By October 1st, technicians began removing Starship Mk1’s four flaps, flap shrouds, and leg shrouds, finally culminating in the separation of the rocket prototype’s upper and lower halves.
The fact that neither Musk or SpaceX spokespersons noted that Starship wasn’t actually complete is at least a little unsavory, although it’s admittedly unsurprising given CEO Elon Musk’s known affinity for grand gestures and events. On a positive note, Starship’s mock-assembly likely served as an excellent learning experience for the Boca Chica team and thankfully only seems to have caused a week or two of delay.
Rapid progress in Boca Chica
Despite the mild disruption of dressing Starship Mk1 up for Musk’s presentation, SpaceX Boca Chica has made a huge amount of progress in the five weeks since. Barely three weeks after the rocket’s forward flaps (canards) were removed, SpaceX technicians began the reinstallation process with one major visible difference: a massive motorcycle-sized actuator.
On the first round of installations-for-show, Starship Mk1’s flaps featured no such mechanism, confirming suspicions that much of the hardware installed at the last second was not quite finished or was only being installed for Musk (and practice). The appearance of a previously unseen actuator mechanism on the first reinstalled canard suggests that this time around, SpaceX is installing Starship’s flaps with their final purpose of controlling Starship’s free-fall in mind.
Instead of copying Falcon 9’s proven method of vertical launch and vertical landing, SpaceX is taking a more radical approach with Starship that will see the spacecraft reenter Earth’s atmosphere belly-first, slow its forward speed to near-zero, and fall directly down for approximately 25 km (15.5 mi), using its flaps like a skydiver’s limbs. Perhaps just a few hundred meters above the ground, Starship will finally perform an aggressive flip maneuver, igniting its Raptors while sideways, swerving to neutralize that horizontal velocity, and finally landing on six small legs.
In this sense, although they certainly look the part, Starship’s aerodynamic control surfaces are very explicitly not wings and are instead meant to interact with the atmosphere at an almost 90-degree angle of attack (AoA). In line with that strategy, they only have to actuate with a single degree of freedom, drastically simplifying Starship’s control surfaces.
Similar to Starship Mk1’s newly filled-out canard actuators, SpaceX technicians have installed two massive hinges/mounts for Starship’s larger after flaps. Aft flap installation will likely start as soon as SpaceX technicians have installed the bulk of Starship Mk1’s external plumbing and wiring, a milestone that appears to be fast approaching.
Starship Mk1’s lower half was unexpectedly moved about a mile to SpaceX’s nearby launch facilities prior to the installation of its nose section, meaning that SpaceX will likely have to transport the nose to the launch pad for final mating. It’s unclear what tests SpaceX specifically plans to kick off Starship Mk1’s pre-flight preparations with, but it’s safe to assume that the most imminent milestone is a wet dress rehearsal (WDR), possibly preceded by a tank proof test.
The latter procedure would be designed to prove that Starship Mk1’s pressure vessel is both leakproof and structurally sound and would nominally involve filling the spacecraft’s tanks with a neutral fluid (likely water or liquid nitrogen). A WDR would see SpaceX load Starship as if preparing for launch (requiring liquid oxygen, methane, nitrogen, and helium) but stopping just prior to the engine ignition and liftoff that would otherwise follow. Although unlikely, a WDR could result in a massive fire or explosion if Starship were to lose structural integrity during the test, which is why the aforementioned neutral testing is typically performed first when handling brand new launch vehicles.
Finally, assuming Starship Mk1 successfully passes the above tests, SpaceX will use the vehicle to perform Raptor’s first triple-engine static fire test. That static fire will likely be the final major test activity before SpaceX readies Starship Mk1 for its 20-km flight debut, which will serve as a more or less full-fidelity test of Starship’s exotic skydiver-like landing.
Regardless of how exactly Starship Mk1’s imminent test campaign will play out, SpaceX has road closures scheduled on November 7th, 8th, and 12th. Right now, it’s anyone’s guess what is planned for Thursday and Friday, but it could potentially involve a tank proof test, launch pad checkouts, propellant loading, or something more benign, like transporting Starship’s nose section to the pad for final installation. Stay tuned!
Check out Teslarati’s Marketplace! We offer Tesla accessories, including for the Tesla Cybertruck and Tesla Model 3.
Tesla is continuing to push the boundaries of vehicle dynamics, as its latest published patent, US12654505B2, or “Suspension Actuator System for a Vehicle,’ which has finally been pushed through.
The design, which is credited to inventors Brian Lee Doorlag, Avraham Kagan, and Justin Sill, introduces a sophisticated hybrid suspension design that blends active motor-driven control with strategic passive elements to deliver superior ride quality, energy efficiency, and resilience against road imperfections, especially potholes.
Suspension Actuator System for a Vehicle@Tesla‘s US20240383297A1 patent introduces an innovative suspension actuator system that transforms vehicle suspension control through an intelligent combination of active and passive control elements.
By implementing both series and… https://t.co/vRvlOu3Dql pic.twitter.com/2WriXgpOvr
— SETI Park (@seti_park) November 27, 2024
At the heart of the system is an active control element powered by an electric motor. This motor drives a belt connected to a ball nut assembly and threaded screw, which adjusts the effective length of the suspension strut in real time.
By extending or retracting, the actuator can lift or lower the wheel more accurately, which can end up countering road disturbances. Sensors, including accelerometers and wheel position monitors, feed data to a suspension control system that processes inputs and commands the motor instantly.
This active component doesn’t work alone. A low-rate air spring mounts in parallel with the actuator. Its primary role is to offset much of the vehicle’s static weight, dramatically reducing the power demand on the motor.
Without this, the active system would constantly fight gravity, draining energy and generating heat. The air spring handles steady-state loads efficiently, allowing the motor to focus on dynamic adjustments.
Complementing this is a series of passive control elements—a spring and an adaptive damper—placed between the actuator and the wheel. This setup filters high-frequency vibrations before they reach the active motor, preventing it from overworking on minor inputs. The adaptive damper, potentially magnetorheological or valve-controlled, further tunes damping electronically for optimal comfort and stability.
How It Differs from Traditional Suspensions
Traditional passive suspensions compromise between comfort and handling, while pure active systems can be power-hungry and complex. Tesla’s hybrid approach resolves this by delegating tasks: the parallel air spring manages weight and low-frequency body motions, the series elements absorb rapid vibrations, and the active actuator tackles larger, lower-frequency events.
The result is a smoother, more isolated cabin experience. High-frequency road noise and harshness diminish, while the vehicle maintains precise control during cornering or acceleration. Energy efficiency improves, too—lower motor loads mean reduced battery drain, potentially extending range in electric vehicles.
How It Mitigates Potholes Specifically
Potholes are a major challenge because they provide a sudden drop to the wheel plunge, jarring the body of the vehicle, risking damage. The patent explicitly addresses this. Upon detecting a pothole (via sensors or predictive mapping), the control system activates
the motor to retract the strut, effectively pulling the wheel upward to minimize downward excursion. The series spring/damper cushions the impact, while the parallel air spring maintains overall support.
This proactive “wheel retraction” prevents sharp jolts, preserving passenger comfort and protecting components. Integrated with Tesla’s road roughness mapping patents, the system could anticipate potholes from fleet data, enabling preemptive adjustments for even smoother navigation.
Future Implications for Tesla Vehicles
This technology builds on Tesla’s existing adaptive dampers and air suspension that is seen in Cybertruck, but advances toward fully active control. It could roll out to future models, including refreshed Cybertrucks or next-gen vehicles, enhancing both daily drivability and off-road capability. By minimizing power use and complexity, it aligns with Tesla’s goals of efficiency and scalability.
In summary, US12654505B2 exemplifies Tesla’s engineering philosophy: intelligent integration over brute force. This hybrid suspension promises quieter, more comfortable rides and robust pothole defense, potentially setting a new standard for automotive comfort. As Tesla iterates, drivers can look forward to roads feeling far less rough.
The Tesla Cybercab got a huge nod of support from a Texas Department of Transportation official, who said the all-electric ride-hailing vehicle is “a tangible example of how quickly our transportation system is evolving.”
The Cybercab was present at the Texas Department of Transportation’s Texas Innovation Invitational, an event held each year that allows innovative companies to showcase advancements in transportation.
Tesla Cybercab specs revealed: range, curb weight, range ratings, and more
Marc Williams, the Texas Department of Transportation’s Executive Director, sat in a Cybercab and shared his thoughts in an extensive post on LinkedIn.
Williams’s comments show how Tesla, with its Cybercab, is leading the charge of passenger travel and how it’s changing so rapidly. He notes the absence of traditional driving controls as a telltale sign that the Cybercab is a catalyst for major automotive change, taking controls from drivers and turning them into full-time passengers.
“Observing this vehicle firsthand–from its design and butterfly doors to the cargo trunk configuration–provides a tangible example of how quickly our transportation system is evolving. Sitting inside the cabin, the complete absence of traditional driver controls underscores a significant shift in mobility and vehicle design. No steering wheel, no accelerator, no brake. Only a single touchscreen monitor.”
Tesla has had a great relationship with the State of Texas, especially with its Robotaxi ambitions. Currently, Texas has Tesla Robotaxi operating in multiple cities: Dallas, Austin, San Antonio, and Houston. The company’s main manufacturing plant is also located just outside Austin, and Tesla moved its headquarters to the state several years ago.
Texas DOT Executive Director Marc Williams experienced the production version of @Tesla CyberCab firsthand earlier today at the 2026 Texas Innovation Invitational #CyberCab #FSD @SawyerMerritt @TeslaNewswire pic.twitter.com/izoGOWaGz6
— Ash_Alpha (@durai_ashwin08) June 17, 2026
The Cybercab is a purpose-built, fully autonomous, two-passenger Robotaxi vehicle designed specifically for ride-hailing services. Tesla has said for years it would be built without a steering wheel or pedals present, although there is still quite a bit of debate among the community regarding that potential.
Earlier this week, we received official word that the EPA had provided the Cybercab with a Certificate of Conformity, giving Tesla permission to enter the vehicle into the chain of public commerce. It is officially ready for roads.
The big question for Tesla remains: Can it solve self-driving before the steering-wheel-less Cybercab officially enters production?
Elon Musk
The Boring Company just doubled its tunneling power in Nashville
The Boring Company’s Prufrock MB2 is commissioned and ready to mine beneath Nashville’s streets.
The Boring Company’s second tunnel boring machine, Prufrock MB2, is officially ready to dig in Nashville. The company confirmed the news on X, posting: “Prufrock-MB2 is ready to mine in Nashville! MB2 commissioning is complete, including the brief 11 rpm rotation shown here. Will MB2 catch up to MB1, who had quite the head start? And Prufrock-MB3 ships in August!”
MB2 arrives with meaningful improvements over its predecessor. Lessons learned from the launch and operation of MB1 have already been applied to MB2 to improve efficiency and prepare the machine for launch.
Traditional tunnel boring machines operate in a stop-and-go cycle, digging roughly five feet, halt, erect precast concrete segments to line the tunnel wall, then resume. That repeated interruption is one of the main reasons conventional tunneling is slow and expensive. Prufrock is designed to install the tunnel liner simultaneously with mining, eliminating the need to stop every five feet. The machine also skips the need for excavated launch pits. Prufrock arrives on a truck, tilts down, and launches into the ground within 24 hours. And when the tunnel is complete, it emerges from the ground and drives to its next launch site on a trailer, eliminating the need for expensive cranes or pit excavation. The machine is also fully electric and runs with zero people in the tunnel during normal operations, controlled remotely from a surface operations center.
Prufrock-MB2 is ready to mine in Nashville! MB2 commissioning is complete, including the brief 11 rpm rotation shown here.
Will MB2 catch up to MB1, who had quite the head start?
And Prufrock-MB3 ships in August! pic.twitter.com/TTrMql2aRg
— The Boring Company (@boringcompany) June 17, 2026
It won’t be long before we hear of another major update on The Boring Company’s Music City Loop project – a planned underground transit network beneath Nashville that would move passengers in electric vehicles through a series of tunnels at highway speeds, and bypassing surface traffic entirely. Nashville was selected in part because of its strong rock conditions that suits the Prufrock machines well, and relatively less regulatory hurdles.
Progress has been steady on multiple fronts. All 37 permits and approvals required ahead of tunneling have been obtained, out of 45 total. Key wins include a fully executed TDOT tunnel permit authorizing 25 miles of tunnel, unanimous airport authority approval for a Nashville International Airport station, and the city’s first residential station agreement serving downtown tower residents.
With MB1 already tunneling, MB2 now commissioned, and MB3 shipping in August, Nashville is becoming something of a live proving ground for scaled tunnel boring. The broader ambition is not limited to one city. The Boring Company’s stated goal is to make underground transportation a practical alternative to surface roads across major metro areas. Nashville is one of many cities, including a successful Las Vegas tunnel system, where that idea is being put to the test at real speed.
Tesla patent aims to improve common on-road complaint
Tesla Cybercab gets huge nod of support from Texas DOT official
