News
SpaceX sets stage for Starship booster’s first 33-engine static fire
SpaceX has set the stage for a record-breaking Starship booster static fire after the rocket completed a complex fueling test and launch rehearsal earlier this week.
On January 25th, a tower the size of a skyscraper activated a pair of giant mechanical arms to disassemble the largest rocket ever built. The arms carefully grabbed Starship using hard points under its flaps and lifted the 50-meter-tall second stage and spacecraft off of Super Heavy Booster 7. Nicknamed Mechazilla, the robot lowered the hundred-ton (~220,000+ lbs) vehicle hundreds of feet onto a waiting stand and eventually let go. On January 26th, SpaceX transported Ship 24 back to its Starbase, Texas factory for finishing touches.
Booster 7 remained installed on Starbase’s donut-shaped orbital launch mount, which uses clamps and umbilicals to hold Starship in place and power, fuel, and pressurize Super Heavy. In theory, the next time Booster 7 leaves that launch mount, it will do so under its own power. But first, SpaceX must ensure that that unprecedented power can be controlled (and survived).
The update that's rolling out to the fleet makes full use of the front and rear steering travel to minimize turning circle. In this case a reduction of 1.6 feet just over the air— Wes (@wmorrill3) April 16, 2024
This, unfortunately, is far from the first iteration of this story. SpaceX has been seemingly close to the milestone at many points over the last year and a half. In September 2021, for example, CEO Elon Musk reported that Super Heavy Booster 4 would attempt the first static fire on Starbase’s orbital launch mount later that month. Eleven months later, Super Heavy Booster 7 gave the OLM its inaugural static fire test – albeit with just one of its 33 engines.
In the months following that static fire, Booster 7 completed another single-engine test, a two-engine test, a seven-engine test, a fourteen-engine test, and a long-duration eleven-engine test. All of that slow and steady testing has been fairly successful and caused no major damage to the rocket or pad. But five months after it began, SpaceX has never ignited more than 14 – 42% – of Super Heavy’s 33 Raptor engines at once. That must change before SpaceX can gain enough confidence in Starship for (and convince the FAA to license) an orbital launch attempt.
During Super Heavy B7’s 14-engine static fire, the booster could have produced up to 3220 tons (7.1 million pounds) of thrust. When it ignites all 33 available engines for the first time, its maximum thrust could leap to 7590 tons (16.7 million pounds), beating the next most powerful rocket in history – the Soviet N1 – by nearly 60%. In other words, SpaceX will be attempting something unprecedented in rocketry. Success is far from guaranteed and the worst possible failure mode could almost entirely destroy Starship’s only finished orbital launch site, explaining SpaceX’s unusual caution.
On January 23rd, Ship 24 and Booster 7 completed Starship’s first full wet dress rehearsal (a fueling and launch rehearsal test) on the first try – an extremely impressive achievement for any rocket, let alone the largest in history. With that combined test out of the way, the only unprecedented test standing between Starship and its first orbital launch attempt is a 33-engine Super Heavy static fire.
To reduce risk, Ship 24 was removed from Booster 7. Back at the factory, SpaceX needs to close a few gaps left in its heat shield, and will likely also conduct careful inspections to ensure that the Starship is ready for flight. Unburdened of Ship 24, Booster 7 may finally be on the cusp of the most challenging ground test in Starship and SpaceX history. SpaceX has scheduled 12-hour road closures that could be used for that purpose as early as January 30th, 31st, and February 1st.
Those road closures could be used for Ship 25 static fire testing instead of or in addition to Booster 7. The Super Heavy is also missing an important hydraulic power unit (HPU) that was removed before the wet dress rehearsal. It’s unclear if static fire testing can be conducted without that HPU (one of two), why it was removed, or how long replacing it will take, adding more uncertainty. Nonetheless, it still appears that SpaceX is no more than a few weeks away from Starship’s first 33-engine static fire attempt.
News
Tesla Cybercab display highlights interior wizardry in the small two-seater
Photos and videos of the production Cybercab were shared in posts on social media platform X.
The Tesla Cybercab is currently on display at the U.S. Department of Transportation in Washington, D.C., and observations of the production vehicle are highlighting some of its notable design details.
Photos and videos of the production Cybercab were shared in posts on social media platform X.
Observers of the Cybercab display unit noted that the two-seat Robotaxi provides unusually generous legroom for a vehicle of its size. Based on the vehicle’s video, the compact two-seater appears to offer more legroom than Tesla’s larger vehicles such as the Model Y, Model X, and Cybertruck.
The Cybercab’s layout allows Tesla to dedicate nearly the entire cabin to passengers. The vehicle is designed without a steering wheel or pedals, which helps maximize interior space.
Footage from the display also highlights the Cybercab’s large center screen, which is positioned prominently in front of the passenger bench. The display appears intended to provide entertainment and ride information while the vehicle operates autonomously.
Images of the vehicle also show an additional camera integrated into the Cybercab’s C-pillar. The extra camera appears to expand the vehicle’s field of view, which would be useful as Tesla works toward fully unsupervised Full Self-Driving.
Tesla engineers have previously explained that the Cybercab was designed to be highly efficient both in manufacturing and in operation. Cybercab Lead Engineer Eric E. stated in 2024 that the Robotaxi would be built with roughly half the number of parts used in a Model 3 sedan.
“Two seats unlocks a lot of opportunity aerodynamically. It also means we cut the part count of Cybercab down by a substantial margin. We’re gonna be delivering a car that has roughly half the parts of Model 3 today,” the Tesla engineer said.
The Tesla engineer also noted that the Cybercab’s cargo area can accommodate multiple golf bags, two carry-on suitcases, and two full-size checked bags. The trunk can also fit certain bicycles and a foldable wheelchair depending on size, which is quite impressive for a small car like the Cybercab.
Elon Musk
Elon Musk’s xAI wins permit for power plant supporting AI data centers
The development was reported by CNBC, citing confirmation from the Mississippi Department of Environmental Quality (MDEQ).
Mississippi regulators have approved a permit allowing Elon Musk’s artificial intelligence company xAI to construct a natural gas power plant in Southaven. The facility is expected to support the company’s expanding AI infrastructure tied to its Colossus data center operations near Memphis.
The development was reported by CNBC, citing confirmation from the Mississippi Department of Environmental Quality (MDEQ).
According to the report, regulators “voted to approve the permit” of xAI subsidiary MZX Tech LLC to construct a power plant featuring 41 natural gas-burning turbines “after careful consideration of all public comments and community concerns.”
The Mississippi Department of Environmental Quality stated that the permit followed a regulatory review process that included public comments and community input. Jaricus Whitlock, air division chief for the MDEQ, stated that the project met all applicable environmental standards.
“The proposed PSD permit in front of the board today not only meets all state and federal permitting regulations, but goes above and beyond what is required by law. MDEQ and the EPA agree that not a single person around our facilities will be exposed to unhealthy levels of air pollution,” Whitlock stated.
The planned facility will help provide electricity for xAI’s AI computing infrastructure in the Memphis region.
The Southaven project forms part of xAI’s efforts to scale computing capacity for its artificial intelligence systems.
The company currently operates two major data centers in Memphis, known as Colossus 1 and Colossus 2, which provide computing power for xAI’s Grok AI models. xAI is also planning to build another large data center in Southaven called Macrohardrr, which would be located in a warehouse previously used by GXO Logistics.
Large-scale AI training requires substantial computing power and electricity, prompting technology companies to develop dedicated energy infrastructure for their data centers.
SpaceX President Gwynne Shotwell previously stated that xAI plans to develop 1.2 gigawatts of power capacity for its Memphis-area AI supercomputer site as part of the federal government’s Ratepayer Protection Pledge. The commitment was announced during an event with United States President Donald Trump.
“As part of today’s commitment, we will take extensive additional steps to continue to reduce the costs of electricity for our neighbors. xAI will therefore commit to develop 1.2 GW of power as our supercomputer’s primary power source. That will be for every additional data center as well. We will expand what is already the largest global Megapack power installation in the world,” Shotwell said.
“The installation will provide enough backup power to power the city of Memphis, and more than sufficient energy to power the town of Southaven, Mississippi where the data center resides. We will build new substations and invest in electrical infrastructure to provide stability to the area’s grid.”
Elon Musk
Tesla China teases Optimus robot’s human-looking next-gen hands
The image was shared by Tesla AI’s account on Weibo and later reposted by Tesla community members on X.
A new teaser shared by Tesla’s China team appears to show a pair of unusually human-like hands for Optimus.
The image was shared by Tesla AI’s account on Weibo and later reposted by Tesla community members on X.
As could be seen in the teaser image, the new version of Optimus’ hands features proportions and finger structures that look strikingly similar to those of a human hand. Their appearance suggests that they might have dexterity approaching that of a human hand.
If the image reflects a new generation of Optimus’ hands, it could indicate Tesla is continuing to refine one of the most critical components of its humanoid robot.
Hands are widely viewed as one of the most difficult engineering challenges in robotics. For Optimus to perform complex real-world work, from manufacturing tasks to household activities, its hands would need to be the best in the industry.
Elon Musk has repeatedly described Optimus as Tesla’s most important long-term product. In posts on social media platform X, Musk has stated that Optimus could eventually become the first real-world Von Neumann machine.
In theory, a Von Neumann machine is a self-replicating system capable of building copies of itself using available materials. The concept was originally proposed by mathematician John von Neumann in the mid-20th century.
“Optimus will be the first Von Neumann machine, capable of building civilization by itself on any viable planet,” Musk wrote in a post on X.
If Optimus is expected to carry out complex work autonomously in the future, high levels of dexterity will likely be essential. This makes the development of advanced robotic hands a key step towards Musk’s long-term expectations for the product.
Tesla Cybercab display highlights interior wizardry in the small two-seater
Elon Musk’s xAI wins permit for power plant supporting AI data centers
